MEAN WELL SGA40E series: Wall-Mounted AC/DC Power Adapter - SGA40E09-P1J

Description

MEAN WELL SGA40E09-P1J is a slim Class II wall-mounted AC/DC power adapter with a two-pin European mains plug, providing 9 VDC at 4.44 A with a 40 W maximum rated output. Its standard P1J connector is center-positive. Apply the ambient-temperature and low-input-voltage derating for the installation.

Product Datasheet

Download MEAN WELL SGA40E Datasheet (PDF)

The SGA40E section is on PDF pages 19, 20, 21, 22, 23. Refer to the complete mechanical drawings and notes when planning installation.

Model and Configuration

Complete order model SGA40E09-P1J.
Series / output code SGA40E; output code 09 identifies 9 VDC. The series number is not the rated power of every voltage version.
Mains connection two-pin European mains plug; Class II construction without a functional-ground connection.
DC connection P1J standard tuning-fork plug: 5.5 mm outside diameter, 2.1 mm inside diameter, 11 ± 0.5 mm length; center positive and outer sleeve negative.
Construction Slim wall-mounted single-output AC/DC adapter in a fully enclosed 94V-0 flame-retardant plastic case.

Output Ratings

DC output voltage 9 VDC.
Rated current / load range 4.44 A rated; 0–4.44 A operating range.
Rated power, maximum 40 W; observe the current rating and all applicable derating.
Ripple and noise, maximum 120 mVp-p under the measurement conditions below.
Voltage tolerance ±5%.
Line regulation ±1%.
Load regulation ±5%.
Efficiency, typical 88% under the general test conditions below.

Input and Timing

Input range 90–264 VAC; frequency 47–63 Hz.
AC input current 1 A at 115 VAC; 0.5 A at 230 VAC.
Cold-start inrush, maximum 40 A at 115 VAC; 70 A at 230 VAC.
Leakage current, maximum 0.25 mA at 240 VAC.
Set-up / rise / hold-up time 500 ms / 100 ms / 12 ms at 115 VAC and 230 VAC, full load.
No-load power Less than 0.075 W for this output-voltage model.
Energy efficiency Level VI; EU ErP and CoC Version 5 compliance.

Protection

Short circuit / overload 110–250% of rated output power for overload protection; hiccup mode with automatic recovery after the fault condition is removed.
Overvoltage 110–140% of rated output voltage; Zener-diode clamping with output short-circuit action.
Limited power source LPS compliance is listed for this series.

Operating Conditions and Derating

Operating temperature −20 to +50°C; apply the temperature derating curve.
Ambient-temperature curve 100% load from −20 to +40°C, decreasing to 70% at +50°C.
Input-voltage curve 80% load at 90 VAC, increasing to 100% at 115 VAC; 100% load from 115 to 264 VAC.
Operating humidity 20–90% RH, non-condensing.
Storage temperature / humidity −20 to +85°C; 10–95% RH, non-condensing.
Temperature coefficient ±0.03%/°C over 0–40°C.
Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes each on X, Y and Z axes.

Observe both input-voltage and temperature limits. The maximum ambient temperature does not imply full rated output.

Mechanical Details and Cable

Body dimensions 75.5 × 32 × 47.5 mm (L × W × H); allow additional clearance for the mains pins and cable.
Mains-plug arrangement two-pin European mains plug is integral to the adapter; no detachable AC cord is required.
DC cable UL2468 16 AWG; 1000 mm +150/−0 mm for this output-voltage version.
Catalogue unit weight 165 g, catalogue packing reference per unit; not a measured net or shipping weight.

Use the mechanical drawing on PDF page 21 for plug clearance and cable arrangement. Check socket dimensions and polarity before connection.

Optional DC Plugs and Accessories

Tuning-fork choices P1I: 5.5 / 2.1 / 9.5; P1L: 5.5 / 2.5 / 9.5; P1M: 5.5 / 2.5 / 11; P1IR: 5.5 / 2.1 / 9.5; P1JR: 5.5 / 2.1 / 11; P1LR: 5.5 / 2.5 / 9.5; P1MR: 5.5 / 2.5 / 11 mm (outside diameter / inside diameter / length). Codes ending in R are right-angled; the others are straight. Available as requested plug configurations.
Barrel choices P2I: 5.5 / 2.1 / 9.5; P2J: 5.5 / 2.1 / 11; P2L: 5.5 / 2.5 / 9.5; P2M: 5.5 / 2.5 / 11; P2IR: 5.5 / 2.1 / 9.5; P2JR: 5.5 / 2.1 / 11; P2LR: 5.5 / 2.5 / 9.5; P2MR: 5.5 / 2.5 / 11 mm (outside diameter / inside diameter / length). R suffix indicates right-angle form. Factory-customized plug options.
Locking choices P2S (S761K): 5.53 / 2.03 / 12.06; P2K (761K): 5.53 / 2.54 / 12.06; P2C (S760K): 5.53 / 2.03 / 9.52; P2D (760K): 5.53 / 2.54 / 9.52 mm (outside diameter / inside diameter / length). SWITCHCRAFT original or equivalent; factory-customized plug options.
Minimum-pin choices P3A: 2.35 / 0.7 / 11; P3B: 4.0 / 1.7 / 11; P3C: 4.75 / 1.7 / 11 mm (outside diameter / inside diameter / length). EIAJ equivalent. Available as requested plug configurations.
Center-pin choices P4A: 5.5 / 3.4 / 11 / 1.0; P4B: 6.5 / 4.4 / 11 / 1.4; P4C: 7.4 / 5.1 / 11 / 0.6 mm (outside / inside / length / center-pin diameter). EIAJ equivalent.
R6B, locking 3-pin male KYCON KPPX-3P equivalent; pins 1 and 3 = +Vo, pin 2 = −Vo.
R7B, locking 4-pin male KYCON KPPX-4P equivalent; pins 1 and 4 = +Vo, pins 2 and 3 = −Vo.
R7BF, locking 4-pin female KYCON KPJX-CM-4S equivalent; pins 1 and 4 = +Vo, pins 2 and 3 = −Vo. Factory-customized option.

The standard supplied configuration is the P1J order model. Alternative DC plugs are available by customer request. Confirm the exact assembly before ordering.

Accessory current limits do not increase the power-adapter output rating. Check mating dimensions, polarity and the lower of the power-adapter, cable and connector current ratings.

Custom stripped and tinned leads are illustrated: lead 1 ribbed = +Vo; lead 2 lettered = −Vo. The standard drawing shows L = 25 mm and L1 = 10 mm; lengths may be customized. Confirm the lead assembly when ordering.

Safety and EMC

Listed safety approvals TUV EN60950-1 and EAC TP TC 004.
Dielectric withstand Input to output: 4242 VDC.
Insulation resistance Input to output: 100 MΩ at 500 VDC, 25°C and 70% RH.
Conducted / radiated emissions EN55032 (CISPR32), Class B.
Harmonics / flicker EN61000-3-2, Class A; EN61000-3-3.
ESD immunity EN61000-4-2: Level 3, 8 kV air; Level 2, 4 kV contact.
RF field / conducted RF EN61000-4-3: Level 2, 3 V/m; EN61000-4-6: Level 2, 3 V.
EFT / surge EN61000-4-4: Level 2, 1 kV; EN61000-4-5: Level 3, 1 kV line-to-neutral.
Magnetic field immunity EN61000-4-8: Level 1, 1 A/m.
Voltage dips / interruptions EN61000-4-11: >95% dip for 0.5 period; 30% dip for 25 periods; >95% interruption for 250 periods.

Final equipment EMC performance depends on the complete installation and must be checked with the connected equipment.

Measurement Conditions and Reliability

General test conditions Unless otherwise specified: 230 VAC input, rated load, 25°C and 70% RH.
DC voltage set point Measured at the output plug at 50% load.
Ripple/noise measurement 20 MHz bandwidth; 12-inch twisted pair terminated with 0.1 µF and 47 µF capacitors.
MTBF, minimum 400 thousand hours, MIL-HDBK-217F at 25°C.
Catalogue life condition 3 years at 100% load, 40°C and 12 hours/day.
Manufacturer warranty 3 years, subject to manufacturer warranty terms.
Catalogue revision 2019-11-07; combined PDF pages 19–23.

Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input voltage at rated load; load regulation is measured from 10% to 100% rated load.

Applications and Selection

Suitable application examples include consumer electronics, telecommunications equipment, office equipment and industrial equipment.

Choose the exact mains-plug version, DC voltage, current capacity and output connector required by the equipment.

MEAN WELL SGA40E series: Wall-Mounted AC/DC Power Adapter - SGA40E09-P1J

Product form

MEAN WELL SGA40E09-P1J is a slim Class II wall-mounted AC/DC power adapter with a two-pin European mains plug, providing 9... Read more

$103.99 Incl. VAT

    • Guaranteed secure & safe checkout.

      shop pay

    Description

    MEAN WELL SGA40E09-P1J is a slim Class II wall-mounted AC/DC power adapter with a two-pin European mains plug, providing 9 VDC at 4.44 A with a 40 W maximum rated output. Its standard P1J connector is center-positive. Apply the ambient-temperature and low-input-voltage derating for the installation.

    Product Datasheet

    Download MEAN WELL SGA40E Datasheet (PDF)

    The SGA40E section is on PDF pages 19, 20, 21, 22, 23. Refer to the complete mechanical drawings and notes when planning installation.

    Model and Configuration

    Complete order model SGA40E09-P1J.
    Series / output code SGA40E; output code 09 identifies 9 VDC. The series number is not the rated power of every voltage version.
    Mains connection two-pin European mains plug; Class II construction without a functional-ground connection.
    DC connection P1J standard tuning-fork plug: 5.5 mm outside diameter, 2.1 mm inside diameter, 11 ± 0.5 mm length; center positive and outer sleeve negative.
    Construction Slim wall-mounted single-output AC/DC adapter in a fully enclosed 94V-0 flame-retardant plastic case.

    Output Ratings

    DC output voltage 9 VDC.
    Rated current / load range 4.44 A rated; 0–4.44 A operating range.
    Rated power, maximum 40 W; observe the current rating and all applicable derating.
    Ripple and noise, maximum 120 mVp-p under the measurement conditions below.
    Voltage tolerance ±5%.
    Line regulation ±1%.
    Load regulation ±5%.
    Efficiency, typical 88% under the general test conditions below.

    Input and Timing

    Input range 90–264 VAC; frequency 47–63 Hz.
    AC input current 1 A at 115 VAC; 0.5 A at 230 VAC.
    Cold-start inrush, maximum 40 A at 115 VAC; 70 A at 230 VAC.
    Leakage current, maximum 0.25 mA at 240 VAC.
    Set-up / rise / hold-up time 500 ms / 100 ms / 12 ms at 115 VAC and 230 VAC, full load.
    No-load power Less than 0.075 W for this output-voltage model.
    Energy efficiency Level VI; EU ErP and CoC Version 5 compliance.

    Protection

    Short circuit / overload 110–250% of rated output power for overload protection; hiccup mode with automatic recovery after the fault condition is removed.
    Overvoltage 110–140% of rated output voltage; Zener-diode clamping with output short-circuit action.
    Limited power source LPS compliance is listed for this series.

    Operating Conditions and Derating

    Operating temperature −20 to +50°C; apply the temperature derating curve.
    Ambient-temperature curve 100% load from −20 to +40°C, decreasing to 70% at +50°C.
    Input-voltage curve 80% load at 90 VAC, increasing to 100% at 115 VAC; 100% load from 115 to 264 VAC.
    Operating humidity 20–90% RH, non-condensing.
    Storage temperature / humidity −20 to +85°C; 10–95% RH, non-condensing.
    Temperature coefficient ±0.03%/°C over 0–40°C.
    Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes each on X, Y and Z axes.

    Observe both input-voltage and temperature limits. The maximum ambient temperature does not imply full rated output.

    Mechanical Details and Cable

    Body dimensions 75.5 × 32 × 47.5 mm (L × W × H); allow additional clearance for the mains pins and cable.
    Mains-plug arrangement two-pin European mains plug is integral to the adapter; no detachable AC cord is required.
    DC cable UL2468 16 AWG; 1000 mm +150/−0 mm for this output-voltage version.
    Catalogue unit weight 165 g, catalogue packing reference per unit; not a measured net or shipping weight.

    Use the mechanical drawing on PDF page 21 for plug clearance and cable arrangement. Check socket dimensions and polarity before connection.

    Optional DC Plugs and Accessories

    Tuning-fork choices P1I: 5.5 / 2.1 / 9.5; P1L: 5.5 / 2.5 / 9.5; P1M: 5.5 / 2.5 / 11; P1IR: 5.5 / 2.1 / 9.5; P1JR: 5.5 / 2.1 / 11; P1LR: 5.5 / 2.5 / 9.5; P1MR: 5.5 / 2.5 / 11 mm (outside diameter / inside diameter / length). Codes ending in R are right-angled; the others are straight. Available as requested plug configurations.
    Barrel choices P2I: 5.5 / 2.1 / 9.5; P2J: 5.5 / 2.1 / 11; P2L: 5.5 / 2.5 / 9.5; P2M: 5.5 / 2.5 / 11; P2IR: 5.5 / 2.1 / 9.5; P2JR: 5.5 / 2.1 / 11; P2LR: 5.5 / 2.5 / 9.5; P2MR: 5.5 / 2.5 / 11 mm (outside diameter / inside diameter / length). R suffix indicates right-angle form. Factory-customized plug options.
    Locking choices P2S (S761K): 5.53 / 2.03 / 12.06; P2K (761K): 5.53 / 2.54 / 12.06; P2C (S760K): 5.53 / 2.03 / 9.52; P2D (760K): 5.53 / 2.54 / 9.52 mm (outside diameter / inside diameter / length). SWITCHCRAFT original or equivalent; factory-customized plug options.
    Minimum-pin choices P3A: 2.35 / 0.7 / 11; P3B: 4.0 / 1.7 / 11; P3C: 4.75 / 1.7 / 11 mm (outside diameter / inside diameter / length). EIAJ equivalent. Available as requested plug configurations.
    Center-pin choices P4A: 5.5 / 3.4 / 11 / 1.0; P4B: 6.5 / 4.4 / 11 / 1.4; P4C: 7.4 / 5.1 / 11 / 0.6 mm (outside / inside / length / center-pin diameter). EIAJ equivalent.
    R6B, locking 3-pin male KYCON KPPX-3P equivalent; pins 1 and 3 = +Vo, pin 2 = −Vo.
    R7B, locking 4-pin male KYCON KPPX-4P equivalent; pins 1 and 4 = +Vo, pins 2 and 3 = −Vo.
    R7BF, locking 4-pin female KYCON KPJX-CM-4S equivalent; pins 1 and 4 = +Vo, pins 2 and 3 = −Vo. Factory-customized option.

    The standard supplied configuration is the P1J order model. Alternative DC plugs are available by customer request. Confirm the exact assembly before ordering.

    Accessory current limits do not increase the power-adapter output rating. Check mating dimensions, polarity and the lower of the power-adapter, cable and connector current ratings.

    Custom stripped and tinned leads are illustrated: lead 1 ribbed = +Vo; lead 2 lettered = −Vo. The standard drawing shows L = 25 mm and L1 = 10 mm; lengths may be customized. Confirm the lead assembly when ordering.

    Safety and EMC

    Listed safety approvals TUV EN60950-1 and EAC TP TC 004.
    Dielectric withstand Input to output: 4242 VDC.
    Insulation resistance Input to output: 100 MΩ at 500 VDC, 25°C and 70% RH.
    Conducted / radiated emissions EN55032 (CISPR32), Class B.
    Harmonics / flicker EN61000-3-2, Class A; EN61000-3-3.
    ESD immunity EN61000-4-2: Level 3, 8 kV air; Level 2, 4 kV contact.
    RF field / conducted RF EN61000-4-3: Level 2, 3 V/m; EN61000-4-6: Level 2, 3 V.
    EFT / surge EN61000-4-4: Level 2, 1 kV; EN61000-4-5: Level 3, 1 kV line-to-neutral.
    Magnetic field immunity EN61000-4-8: Level 1, 1 A/m.
    Voltage dips / interruptions EN61000-4-11: >95% dip for 0.5 period; 30% dip for 25 periods; >95% interruption for 250 periods.

    Final equipment EMC performance depends on the complete installation and must be checked with the connected equipment.

    Measurement Conditions and Reliability

    General test conditions Unless otherwise specified: 230 VAC input, rated load, 25°C and 70% RH.
    DC voltage set point Measured at the output plug at 50% load.
    Ripple/noise measurement 20 MHz bandwidth; 12-inch twisted pair terminated with 0.1 µF and 47 µF capacitors.
    MTBF, minimum 400 thousand hours, MIL-HDBK-217F at 25°C.
    Catalogue life condition 3 years at 100% load, 40°C and 12 hours/day.
    Manufacturer warranty 3 years, subject to manufacturer warranty terms.
    Catalogue revision 2019-11-07; combined PDF pages 19–23.

    Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input voltage at rated load; load regulation is measured from 10% to 100% rated load.

    Applications and Selection

    Suitable application examples include consumer electronics, telecommunications equipment, office equipment and industrial equipment.

    Choose the exact mains-plug version, DC voltage, current capacity and output connector required by the equipment.

    Recently viewed products

      Footer image

      © 2026 MEAN WELL, ,

      • US (USD $) US (USD $)
      • Ach Direct Debit
      • AliPay
      • Amazon
      • American Express
      • Apple Pay
      • Diners Club
      • Discover
      • Google Pay
      • Mastercard
      • PayPal
      • Shop Pay
      • USDC
      • Visa