Show previous products

• 

  View options

  MEAN WELL LRS-50 series: enclosed AC/DC switching power supply - LRS-50-48

  MEAN WELL LRS-50-48 is a single-output enclosed switching power supply with a 48 V DC output, 1.1 A rated current and 52.8 W rated output power. Universal AC input / full range. Free-air convection; no fan. Download MEAN WELL LRS-50 Datasheet (PDF) The combined LRS catalog includes this series on PDF pages 5–8. Specifications: page 6; mechanical drawing: page 8. Model and Output Specifications Complete model LRS-50-48 Series LRS-50 Output-voltage code 48 = 48 V DC nominal output Rated output voltage 48 V DC Rated output current 1.1 A Output current range 0 to 1.1 A Rated output power 52.8 W Output voltage adjustment 43.2 to 52.8 V Ripple and noise, maximum 200 mVp-p Voltage tolerance ±1.0% Line regulation ±0.5% Load regulation ±0.5% Efficiency, typical 90% at the stated test conditions 230 VAC input, rated load, 25°C ambient unless otherwise stated. Ripple/noise test: 20 MHz bandwidth; 12-inch twisted-pair wire terminated with 0.1 µF and 47 µF parallel capacitors. Voltage tolerance includes setup tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load; load regulation is measured from 0% to 100% rated load. Input and Timing AC input range 85 to 264 VAC Input range selection Universal AC input / full range DC input range 120 to 373 VDC Input frequency 47 to 63 Hz AC input current, typical 0.95A/115VAC 0.56A/230VAC Inrush current, typical Cold start 45A/230VAC Leakage current <0.75mA / 240VAC Setup / rise time 1000 / 30 ms at 230 VAC; 2000 / 30 ms at 115 VAC, full load Hold-up time, typical 30 ms at 230 VAC; 12 ms at 115 VAC, full load Transient input withstand 300 VAC for 5 seconds; this is a surge condition, not the continuous input rating Full load; setup at cold first start. Rapid on/off cycling can increase setup time. Protection and Recovery Short-circuit protection Included Overload 110 to 150% of rated output power. Hiccup; automatically recovers after fault condition is removed. Overvoltage protection 55.2 to 67.8 V. Shut down output; re-power on to recover. Environment and Cooling Ambient operating temperature -30 to 70 °C; apply the temperature and input-voltage derating curves Cooling Free-air convection; no fan Working humidity 20 ~ 90% RH non-condensing Storage temperature / humidity -40 ~ +85°C, 10 ~ 95% RH non-condensing Temperature coefficient ±0.03%/°C (0 ~ 50°C) Operating altitude Up to 5,000 m as stated for this series; the applicable overvoltage category and temperature derating impose additional limits. Overvoltage category Category III up to 2,000 m under the standards specified in this series datasheet. This is an insulation category, separate from the output-overvoltage protection threshold. Higher-altitude temperature derating For operation above 2,000 m, reduce the permitted ambient temperature by 5 °C per additional 1,000 m. Verify the applicable insulation/approval limits for the installation. Full rated output is not available at every point within the temperature and input ranges. Use the ambient-temperature and static input-voltage curves on PDF page 7 for this model and installation orientation. Dimensions and Installation Overall dimensions (L × W × H) 99 × 82 × 30 mm Case number 239A Drawing tolerance ±1 mm Mounting-hole callouts 2-M3 L=3.0; 2-M3 L=5 Terminal 1 AC/L Terminal 2 AC/N Terminal 3 FG (protective earth) Terminal 4 DC OUTPUT -V Terminal 5 DC OUTPUT +V Use the mechanical drawing on PDF page 8 to locate the holes and confirm the permitted screw penetration for the selected mounting face. The M3/M4 callouts are mounting dimensions, not accessory ordering codes. Match wiring, protective-earth connection and output polarity to the terminal markings. Keep ventilation openings clear for convection cooling. This enclosed supply is a component for installation inside final equipment. Complete installation and electrical work using the manufacturer’s installation instructions and the applicable equipment requirements. Reference Weight Catalog reference per unit 210 g This value is the per-unit reference in the manufacturer’s PACKING row. It is not a measured net weight or a quotation for the complete shipping package. Application and Datasheet Notes EMC results are for a component installed on the manufacturer’s specified test plate. The finished equipment must be checked again for EMC compliance. Safety approvals and regional exceptions depend on the exact model and datasheet revision; refer to the linked specification and applicable certificates when selecting the unit. Additional Manufacturer Data Vibration test 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes MTBF reference 3149.8K hrs min. Telcordia SR-332 (Bellcore) ; 561.6Khrs min. MIL-HDBK-217F (25°C) Dielectric withstand I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC Power indication LED power-on indicator Manufacturer datasheet warranty 3 years; subject to the manufacturer’s applicable warranty terms MTBF is a reliability prediction under the stated method and conditions, not a service-life or warranty-duration guarantee. Source: MEAN WELL LRS-50 datasheet, revision 2025-04-07, in the linked LRS catalog. Use the exact model specification, notes and drawings together when selecting and installing this supply.

  Read more less

  $27.11

  View options

• 

  View options

  MEAN WELL LRS-50 series: enclosed AC/DC switching power supply - LRS-50-36

  MEAN WELL LRS-50-36 is a single-output enclosed switching power supply with a 36 V DC output, 1.45 A rated current and 52.2 W rated output power. Universal AC input / full range. Free-air convection; no fan. Download MEAN WELL LRS-50 Datasheet (PDF) The combined LRS catalog includes this series on PDF pages 5–8. Specifications: page 6; mechanical drawing: page 8. Model and Output Specifications Complete model LRS-50-36 Series LRS-50 Output-voltage code 36 = 36 V DC nominal output Rated output voltage 36 V DC Rated output current 1.45 A Output current range 0 to 1.45 A Rated output power 52.2 W Output voltage adjustment 32.4 to 39.6 V Ripple and noise, maximum 200 mVp-p Voltage tolerance ±1.0% Line regulation ±0.5% Load regulation ±0.5% Efficiency, typical 89% at the stated test conditions 230 VAC input, rated load, 25°C ambient unless otherwise stated. Ripple/noise test: 20 MHz bandwidth; 12-inch twisted-pair wire terminated with 0.1 µF and 47 µF parallel capacitors. Voltage tolerance includes setup tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load; load regulation is measured from 0% to 100% rated load. Input and Timing AC input range 85 to 264 VAC Input range selection Universal AC input / full range DC input range 120 to 373 VDC Input frequency 47 to 63 Hz AC input current, typical 0.95A/115VAC 0.56A/230VAC Inrush current, typical Cold start 45A/230VAC Leakage current <0.75mA / 240VAC Setup / rise time 1000 / 30 ms at 230 VAC; 2000 / 30 ms at 115 VAC, full load Hold-up time, typical 30 ms at 230 VAC; 12 ms at 115 VAC, full load Transient input withstand 300 VAC for 5 seconds; this is a surge condition, not the continuous input rating Full load; setup at cold first start. Rapid on/off cycling can increase setup time. Protection and Recovery Short-circuit protection Included Overload 110 to 150% of rated output power. Hiccup; automatically recovers after fault condition is removed. Overvoltage protection 41.4 to 51.6 V. Shut down output; re-power on to recover. Environment and Cooling Ambient operating temperature -30 to 70 °C; apply the temperature and input-voltage derating curves Cooling Free-air convection; no fan Working humidity 20 ~ 90% RH non-condensing Storage temperature / humidity -40 ~ +85°C, 10 ~ 95% RH non-condensing Temperature coefficient ±0.03%/°C (0 ~ 50°C) Operating altitude Up to 5,000 m as stated for this series; the applicable overvoltage category and temperature derating impose additional limits. Overvoltage category Category III up to 2,000 m under the standards specified in this series datasheet. This is an insulation category, separate from the output-overvoltage protection threshold. Higher-altitude temperature derating For operation above 2,000 m, reduce the permitted ambient temperature by 5 °C per additional 1,000 m. Verify the applicable insulation/approval limits for the installation. Full rated output is not available at every point within the temperature and input ranges. Use the ambient-temperature and static input-voltage curves on PDF page 7 for this model and installation orientation. Dimensions and Installation Overall dimensions (L × W × H) 99 × 82 × 30 mm Case number 239A Drawing tolerance ±1 mm Mounting-hole callouts 2-M3 L=3.0; 2-M3 L=5 Terminal 1 AC/L Terminal 2 AC/N Terminal 3 FG (protective earth) Terminal 4 DC OUTPUT -V Terminal 5 DC OUTPUT +V Use the mechanical drawing on PDF page 8 to locate the holes and confirm the permitted screw penetration for the selected mounting face. The M3/M4 callouts are mounting dimensions, not accessory ordering codes. Match wiring, protective-earth connection and output polarity to the terminal markings. Keep ventilation openings clear for convection cooling. This enclosed supply is a component for installation inside final equipment. Complete installation and electrical work using the manufacturer’s installation instructions and the applicable equipment requirements. Reference Weight Catalog reference per unit 210 g This value is the per-unit reference in the manufacturer’s PACKING row. It is not a measured net weight or a quotation for the complete shipping package. Application and Datasheet Notes EMC results are for a component installed on the manufacturer’s specified test plate. The finished equipment must be checked again for EMC compliance. Safety approvals and regional exceptions depend on the exact model and datasheet revision; refer to the linked specification and applicable certificates when selecting the unit. Additional Manufacturer Data Vibration test 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes MTBF reference 3149.8K hrs min. Telcordia SR-332 (Bellcore) ; 561.6Khrs min. MIL-HDBK-217F (25°C) Dielectric withstand I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC Power indication LED power-on indicator Manufacturer datasheet warranty 3 years; subject to the manufacturer’s applicable warranty terms MTBF is a reliability prediction under the stated method and conditions, not a service-life or warranty-duration guarantee. Source: MEAN WELL LRS-50 datasheet, revision 2025-04-07, in the linked LRS catalog. Use the exact model specification, notes and drawings together when selecting and installing this supply.

  Read more less

  $27.11

  View options

• 

  View options

  MEAN WELL LRS-50 series: enclosed AC/DC switching power supply - LRS-50-24

  MEAN WELL LRS-50-24 is a single-output enclosed switching power supply with a 24 V DC output, 2.2 A rated current and 52.8 W rated output power. Universal AC input / full range. Free-air convection; no fan. Download MEAN WELL LRS-50 Datasheet (PDF) The combined LRS catalog includes this series on PDF pages 5–8. Specifications: page 6; mechanical drawing: page 8. Model and Output Specifications Complete model LRS-50-24 Series LRS-50 Output-voltage code 24 = 24 V DC nominal output Rated output voltage 24 V DC Rated output current 2.2 A Output current range 0 to 2.2 A Rated output power 52.8 W Output voltage adjustment 21.6 to 28.8 V Ripple and noise, maximum 150 mVp-p Voltage tolerance ±1.0% Line regulation ±0.5% Load regulation ±0.5% Efficiency, typical 88% at the stated test conditions 230 VAC input, rated load, 25°C ambient unless otherwise stated. Ripple/noise test: 20 MHz bandwidth; 12-inch twisted-pair wire terminated with 0.1 µF and 47 µF parallel capacitors. Voltage tolerance includes setup tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load; load regulation is measured from 0% to 100% rated load. Input and Timing AC input range 85 to 264 VAC Input range selection Universal AC input / full range DC input range 120 to 373 VDC Input frequency 47 to 63 Hz AC input current, typical 0.95A/115VAC 0.56A/230VAC Inrush current, typical Cold start 45A/230VAC Leakage current <0.75mA / 240VAC Setup / rise time 1000 / 30 ms at 230 VAC; 2000 / 30 ms at 115 VAC, full load Hold-up time, typical 30 ms at 230 VAC; 12 ms at 115 VAC, full load Transient input withstand 300 VAC for 5 seconds; this is a surge condition, not the continuous input rating Full load; setup at cold first start. Rapid on/off cycling can increase setup time. Protection and Recovery Short-circuit protection Included Overload 110 to 150% of rated output power. Hiccup; automatically recovers after fault condition is removed. Overvoltage protection 28.8 to 36.6 V. Shut down output; re-power on to recover. Environment and Cooling Ambient operating temperature -30 to 70 °C; apply the temperature and input-voltage derating curves Cooling Free-air convection; no fan Working humidity 20 ~ 90% RH non-condensing Storage temperature / humidity -40 ~ +85°C, 10 ~ 95% RH non-condensing Temperature coefficient ±0.03%/°C (0 ~ 50°C) Operating altitude Up to 5,000 m as stated for this series; the applicable overvoltage category and temperature derating impose additional limits. Overvoltage category Category III up to 2,000 m under the standards specified in this series datasheet. This is an insulation category, separate from the output-overvoltage protection threshold. Higher-altitude temperature derating For operation above 2,000 m, reduce the permitted ambient temperature by 5 °C per additional 1,000 m. Verify the applicable insulation/approval limits for the installation. Full rated output is not available at every point within the temperature and input ranges. Use the ambient-temperature and static input-voltage curves on PDF page 7 for this model and installation orientation. Dimensions and Installation Overall dimensions (L × W × H) 99 × 82 × 30 mm Case number 239A Drawing tolerance ±1 mm Mounting-hole callouts 2-M3 L=3.0; 2-M3 L=5 Terminal 1 AC/L Terminal 2 AC/N Terminal 3 FG (protective earth) Terminal 4 DC OUTPUT -V Terminal 5 DC OUTPUT +V Use the mechanical drawing on PDF page 8 to locate the holes and confirm the permitted screw penetration for the selected mounting face. The M3/M4 callouts are mounting dimensions, not accessory ordering codes. Match wiring, protective-earth connection and output polarity to the terminal markings. Keep ventilation openings clear for convection cooling. This enclosed supply is a component for installation inside final equipment. Complete installation and electrical work using the manufacturer’s installation instructions and the applicable equipment requirements. Reference Weight Catalog reference per unit 210 g This value is the per-unit reference in the manufacturer’s PACKING row. It is not a measured net weight or a quotation for the complete shipping package. Application and Datasheet Notes EMC results are for a component installed on the manufacturer’s specified test plate. The finished equipment must be checked again for EMC compliance. Safety approvals and regional exceptions depend on the exact model and datasheet revision; refer to the linked specification and applicable certificates when selecting the unit. Additional Manufacturer Data Vibration test 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes MTBF reference 3149.8K hrs min. Telcordia SR-332 (Bellcore) ; 561.6Khrs min. MIL-HDBK-217F (25°C) Dielectric withstand I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC Power indication LED power-on indicator Manufacturer datasheet warranty 3 years; subject to the manufacturer’s applicable warranty terms MTBF is a reliability prediction under the stated method and conditions, not a service-life or warranty-duration guarantee. Source: MEAN WELL LRS-50 datasheet, revision 2025-04-07, in the linked LRS catalog. Use the exact model specification, notes and drawings together when selecting and installing this supply.

  Read more less

  $23.66

  View options

• 

  View options

  MEAN WELL LRS-50 series: enclosed AC/DC switching power supply - LRS-50-15

  MEAN WELL LRS-50-15 is a single-output enclosed switching power supply with a 15 V DC output, 3.4 A rated current and 51 W rated output power. Universal AC input / full range. Free-air convection; no fan. Download MEAN WELL LRS-50 Datasheet (PDF) The combined LRS catalog includes this series on PDF pages 5–8. Specifications: page 6; mechanical drawing: page 8. Model and Output Specifications Complete model LRS-50-15 Series LRS-50 Output-voltage code 15 = 15 V DC nominal output Rated output voltage 15 V DC Rated output current 3.4 A Output current range 0 to 3.4 A Rated output power 51 W Output voltage adjustment 13.5 to 18 V Ripple and noise, maximum 120 mVp-p Voltage tolerance ±1.0% Line regulation ±0.5% Load regulation ±0.5% Efficiency, typical 88% at the stated test conditions 230 VAC input, rated load, 25°C ambient unless otherwise stated. Ripple/noise test: 20 MHz bandwidth; 12-inch twisted-pair wire terminated with 0.1 µF and 47 µF parallel capacitors. Voltage tolerance includes setup tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load; load regulation is measured from 0% to 100% rated load. Input and Timing AC input range 85 to 264 VAC Input range selection Universal AC input / full range DC input range 120 to 373 VDC Input frequency 47 to 63 Hz AC input current, typical 0.95A/115VAC 0.56A/230VAC Inrush current, typical Cold start 45A/230VAC Leakage current <0.75mA / 240VAC Setup / rise time 1000 / 30 ms at 230 VAC; 2000 / 30 ms at 115 VAC, full load Hold-up time, typical 30 ms at 230 VAC; 12 ms at 115 VAC, full load Transient input withstand 300 VAC for 5 seconds; this is a surge condition, not the continuous input rating Full load; setup at cold first start. Rapid on/off cycling can increase setup time. Protection and Recovery Short-circuit protection Included Overload 110 to 150% of rated output power. Hiccup; automatically recovers after fault condition is removed. Overvoltage protection 18.75 to 25.75 V. Shut down output; re-power on to recover. Environment and Cooling Ambient operating temperature -30 to 70 °C; apply the temperature and input-voltage derating curves Cooling Free-air convection; no fan Working humidity 20 ~ 90% RH non-condensing Storage temperature / humidity -40 ~ +85°C, 10 ~ 95% RH non-condensing Temperature coefficient ±0.03%/°C (0 ~ 50°C) Operating altitude Up to 5,000 m as stated for this series; the applicable overvoltage category and temperature derating impose additional limits. Overvoltage category Category III up to 2,000 m under the standards specified in this series datasheet. This is an insulation category, separate from the output-overvoltage protection threshold. Higher-altitude temperature derating For operation above 2,000 m, reduce the permitted ambient temperature by 5 °C per additional 1,000 m. Verify the applicable insulation/approval limits for the installation. Full rated output is not available at every point within the temperature and input ranges. Use the ambient-temperature and static input-voltage curves on PDF page 7 for this model and installation orientation. Dimensions and Installation Overall dimensions (L × W × H) 99 × 82 × 30 mm Case number 239A Drawing tolerance ±1 mm Mounting-hole callouts 2-M3 L=3.0; 2-M3 L=5 Terminal 1 AC/L Terminal 2 AC/N Terminal 3 FG (protective earth) Terminal 4 DC OUTPUT -V Terminal 5 DC OUTPUT +V Use the mechanical drawing on PDF page 8 to locate the holes and confirm the permitted screw penetration for the selected mounting face. The M3/M4 callouts are mounting dimensions, not accessory ordering codes. Match wiring, protective-earth connection and output polarity to the terminal markings. Keep ventilation openings clear for convection cooling. This enclosed supply is a component for installation inside final equipment. Complete installation and electrical work using the manufacturer’s installation instructions and the applicable equipment requirements. Reference Weight Catalog reference per unit 210 g This value is the per-unit reference in the manufacturer’s PACKING row. It is not a measured net weight or a quotation for the complete shipping package. Application and Datasheet Notes EMC results are for a component installed on the manufacturer’s specified test plate. The finished equipment must be checked again for EMC compliance. Safety approvals and regional exceptions depend on the exact model and datasheet revision; refer to the linked specification and applicable certificates when selecting the unit. Additional Manufacturer Data Vibration test 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes MTBF reference 3149.8K hrs min. Telcordia SR-332 (Bellcore) ; 561.6Khrs min. MIL-HDBK-217F (25°C) Dielectric withstand I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC Power indication LED power-on indicator Manufacturer datasheet warranty 3 years; subject to the manufacturer’s applicable warranty terms MTBF is a reliability prediction under the stated method and conditions, not a service-life or warranty-duration guarantee. Source: MEAN WELL LRS-50 datasheet, revision 2025-04-07, in the linked LRS catalog. Use the exact model specification, notes and drawings together when selecting and installing this supply.

  Read more less

  $25.14

  View options

• 

  View options

  MEAN WELL LRS-50 series: enclosed AC/DC switching power supply - LRS-50-3.3

  MEAN WELL LRS-50-3.3 is a single-output enclosed switching power supply with a 3.3 V DC output, 10 A rated current and 33 W rated output power. Universal AC input / full range. Free-air convection; no fan. Download MEAN WELL LRS-50 Datasheet (PDF) The combined LRS catalog includes this series on PDF pages 5–8. Specifications: page 6; mechanical drawing: page 8. Model and Output Specifications Complete model LRS-50-3.3 Series LRS-50 Output-voltage code 3.3 = 3.3 V DC nominal output Rated output voltage 3.3 V DC Rated output current 10 A Output current range 0 to 10 A Rated output power 33 W Output voltage adjustment 2.97 to 3.6 V Ripple and noise, maximum 80 mVp-p Voltage tolerance ±3.0% Line regulation ±0.5% Load regulation ±2.0% Efficiency, typical 80% at the stated test conditions 230 VAC input, rated load, 25°C ambient unless otherwise stated. Ripple/noise test: 20 MHz bandwidth; 12-inch twisted-pair wire terminated with 0.1 µF and 47 µF parallel capacitors. Voltage tolerance includes setup tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load; load regulation is measured from 0% to 100% rated load. At 0–50% load, burst-mode operation on this output-voltage version may cause ripple and noise to exceed the specified value. Input and Timing AC input range 85 to 264 VAC Input range selection Universal AC input / full range DC input range 120 to 373 VDC Input frequency 47 to 63 Hz AC input current, typical 0.95A/115VAC 0.56A/230VAC Inrush current, typical Cold start 45A/230VAC Leakage current <0.75mA / 240VAC Setup / rise time 1000 / 30 ms at 230 VAC; 2000 / 30 ms at 115 VAC, full load Hold-up time, typical 30 ms at 230 VAC; 12 ms at 115 VAC, full load Transient input withstand 300 VAC for 5 seconds; this is a surge condition, not the continuous input rating Full load; setup at cold first start. Rapid on/off cycling can increase setup time. Protection and Recovery Short-circuit protection Included Overload 110 to 150% of rated output power. Hiccup; automatically recovers after fault condition is removed. Overvoltage protection 3.8 to 4.45 V. Shut down output; re-power on to recover. Environment and Cooling Ambient operating temperature -30 to 70 °C; apply the temperature and input-voltage derating curves Cooling Free-air convection; no fan Working humidity 20 ~ 90% RH non-condensing Storage temperature / humidity -40 ~ +85°C, 10 ~ 95% RH non-condensing Temperature coefficient ±0.03%/°C (0 ~ 50°C) Operating altitude Up to 5,000 m as stated for this series; the applicable overvoltage category and temperature derating impose additional limits. Overvoltage category Category III up to 2,000 m under the standards specified in this series datasheet. This is an insulation category, separate from the output-overvoltage protection threshold. Higher-altitude temperature derating For operation above 2,000 m, reduce the permitted ambient temperature by 5 °C per additional 1,000 m. Verify the applicable insulation/approval limits for the installation. Full rated output is not available at every point within the temperature and input ranges. Use the ambient-temperature and static input-voltage curves on PDF page 7 for this model and installation orientation. Dimensions and Installation Overall dimensions (L × W × H) 99 × 82 × 30 mm Case number 239A Drawing tolerance ±1 mm Mounting-hole callouts 2-M3 L=3.0; 2-M3 L=5 Terminal 1 AC/L Terminal 2 AC/N Terminal 3 FG (protective earth) Terminal 4 DC OUTPUT -V Terminal 5 DC OUTPUT +V Use the mechanical drawing on PDF page 8 to locate the holes and confirm the permitted screw penetration for the selected mounting face. The M3/M4 callouts are mounting dimensions, not accessory ordering codes. Match wiring, protective-earth connection and output polarity to the terminal markings. Keep ventilation openings clear for convection cooling. This enclosed supply is a component for installation inside final equipment. Complete installation and electrical work using the manufacturer’s installation instructions and the applicable equipment requirements. Reference Weight Catalog reference per unit 210 g This value is the per-unit reference in the manufacturer’s PACKING row. It is not a measured net weight or a quotation for the complete shipping package. Application and Datasheet Notes EMC results are for a component installed on the manufacturer’s specified test plate. The finished equipment must be checked again for EMC compliance. Safety approvals and regional exceptions depend on the exact model and datasheet revision; refer to the linked specification and applicable certificates when selecting the unit. Additional Manufacturer Data Vibration test 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes MTBF reference 3149.8K hrs min. Telcordia SR-332 (Bellcore) ; 561.6Khrs min. MIL-HDBK-217F (25°C) Dielectric withstand I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC Power indication LED power-on indicator Manufacturer datasheet warranty 3 years; subject to the manufacturer’s applicable warranty terms MTBF is a reliability prediction under the stated method and conditions, not a service-life or warranty-duration guarantee. Source: MEAN WELL LRS-50 datasheet, revision 2025-04-07, in the linked LRS catalog. Use the exact model specification, notes and drawings together when selecting and installing this supply.

  Read more less

  $31.54

  View options

• 

  View options

  MEAN WELL LRS-35 series: enclosed AC/DC switching power supply - LRS-35-48

  MEAN WELL LRS-35-48 is a single-output enclosed switching power supply with a 48 V DC output, 0.8 A rated current and 38.4 W rated output power. Universal AC input / full range. Free-air convection; no fan. Download MEAN WELL LRS-35 Datasheet (PDF) The combined LRS catalog includes this series on PDF pages 1–4. Specifications: page 2; mechanical drawing: page 4. Model and Output Specifications Complete model LRS-35-48 Series LRS-35 Output-voltage code 48 = 48 V DC nominal output Rated output voltage 48 V DC Rated output current 0.8 A Output current range 0 to 0.8 A Rated output power 38.4 W Output voltage adjustment 43.2 to 52.8 V Ripple and noise, maximum 200 mVp-p Voltage tolerance ±1.0% Line regulation ±0.5% Load regulation ±0.5% Efficiency, typical 89% at the stated test conditions 230 VAC input, rated load, 25°C ambient unless otherwise stated. Ripple/noise test: 20 MHz bandwidth; 12-inch twisted-pair wire terminated with 0.1 µF and 47 µF parallel capacitors. Voltage tolerance includes setup tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load; load regulation is measured from 0% to 100% rated load. Input and Timing AC input range 85 to 264 VAC Input range selection Universal AC input / full range DC input range 120 to 373 VDC Input frequency 47 to 63 Hz AC input current, typical 0.7A/115VAC 0.42A/230VAC Inrush current, typical Cold start 45A/230VAC Leakage current <0.75mA / 240VAC Setup / rise time 1000 / 30 ms at 230 VAC; 2000 / 30 ms at 115 VAC, full load Hold-up time, typical 30 ms at 230 VAC; 12 ms at 115 VAC, full load Transient input withstand 300 VAC for 5 seconds; this is a surge condition, not the continuous input rating Full load; setup at cold first start. Rapid on/off cycling can increase setup time. Protection and Recovery Short-circuit protection Included Overload 110 to 150% of rated output power. Hiccup; automatically recovers after fault condition is removed. Overvoltage protection 55.2 to 64.8 V. Shut down output; re-power on to recover. Environment and Cooling Ambient operating temperature -30 to 70 °C; apply the temperature and input-voltage derating curves Cooling Free-air convection; no fan Working humidity 20 ~ 90% RH non-condensing Storage temperature / humidity -40 ~ +85°C, 10 ~ 95% RH non-condensing Temperature coefficient ±0.03%/°C (0 ~ 50°C) Operating altitude Up to 5,000 m as stated for this series; the applicable overvoltage category and temperature derating impose additional limits. Overvoltage category Category III up to 2,000 m under the standards specified in this series datasheet. This is an insulation category, separate from the output-overvoltage protection threshold. Higher-altitude temperature derating For operation above 2,000 m, reduce the permitted ambient temperature by 5 °C per additional 1,000 m. Verify the applicable insulation/approval limits for the installation. Full rated output is not available at every point within the temperature and input ranges. Use the ambient-temperature and static input-voltage curves on PDF page 3 for this model and installation orientation. Dimensions and Installation Overall dimensions (L × W × H) 99 × 82 × 30 mm Case number 239A Drawing tolerance ±1 mm Mounting-hole callouts 2-M3 L=3.0; 2-M3 L=5 Terminal 1 AC/L Terminal 2 AC/N Terminal 3 FG (protective earth) Terminal 4 DC OUTPUT -V Terminal 5 DC OUTPUT +V Use the mechanical drawing on PDF page 4 to locate the holes and confirm the permitted screw penetration for the selected mounting face. The M3/M4 callouts are mounting dimensions, not accessory ordering codes. Match wiring, protective-earth connection and output polarity to the terminal markings. Keep ventilation openings clear for convection cooling. This enclosed supply is a component for installation inside final equipment. Complete installation and electrical work using the manufacturer’s installation instructions and the applicable equipment requirements. Reference Weight Catalog reference per unit 210 g This value is the per-unit reference in the manufacturer’s PACKING row. It is not a measured net weight or a quotation for the complete shipping package. Application and Datasheet Notes EMC results are for a component installed on the manufacturer’s specified test plate. The finished equipment must be checked again for EMC compliance. Safety approvals and regional exceptions depend on the exact model and datasheet revision; refer to the linked specification and applicable certificates when selecting the unit. Additional Manufacturer Data Vibration test 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes MTBF reference 3201.5K hrs min. Telcordia SR-332 (Bellcore) ; 655.5Khrs min. MIL-HDBK-217F (25°C) Dielectric withstand I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC Power indication LED power-on indicator Manufacturer datasheet warranty 3 years; subject to the manufacturer’s applicable warranty terms MTBF is a reliability prediction under the stated method and conditions, not a service-life or warranty-duration guarantee. Source: MEAN WELL LRS-35 datasheet, revision 2025-04-07, in the linked LRS catalog. Use the exact model specification, notes and drawings together when selecting and installing this supply.

  Read more less

  $24.15

  View options

• 

  View options

  MEAN WELL LRS-35 series: enclosed AC/DC switching power supply - LRS-35-36

  MEAN WELL LRS-35-36 is a single-output enclosed switching power supply with a 36 V DC output, 1 A rated current and 36 W rated output power. Universal AC input / full range. Free-air convection; no fan. Download MEAN WELL LRS-35 Datasheet (PDF) The combined LRS catalog includes this series on PDF pages 1–4. Specifications: page 2; mechanical drawing: page 4. Model and Output Specifications Complete model LRS-35-36 Series LRS-35 Output-voltage code 36 = 36 V DC nominal output Rated output voltage 36 V DC Rated output current 1 A Output current range 0 to 1 A Rated output power 36 W Output voltage adjustment 32.4 to 39.6 V Ripple and noise, maximum 200 mVp-p Voltage tolerance ±1.0% Line regulation ±0.5% Load regulation ±0.5% Efficiency, typical 88% at the stated test conditions 230 VAC input, rated load, 25°C ambient unless otherwise stated. Ripple/noise test: 20 MHz bandwidth; 12-inch twisted-pair wire terminated with 0.1 µF and 47 µF parallel capacitors. Voltage tolerance includes setup tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load; load regulation is measured from 0% to 100% rated load. Input and Timing AC input range 85 to 264 VAC Input range selection Universal AC input / full range DC input range 120 to 373 VDC Input frequency 47 to 63 Hz AC input current, typical 0.7A/115VAC 0.42A/230VAC Inrush current, typical Cold start 45A/230VAC Leakage current <0.75mA / 240VAC Setup / rise time 1000 / 30 ms at 230 VAC; 2000 / 30 ms at 115 VAC, full load Hold-up time, typical 30 ms at 230 VAC; 12 ms at 115 VAC, full load Transient input withstand 300 VAC for 5 seconds; this is a surge condition, not the continuous input rating Full load; setup at cold first start. Rapid on/off cycling can increase setup time. Protection and Recovery Short-circuit protection Included Overload 110 to 150% of rated output power. Hiccup; automatically recovers after fault condition is removed. Overvoltage protection 41.4 to 48.6 V. Shut down output; re-power on to recover. Environment and Cooling Ambient operating temperature -30 to 70 °C; apply the temperature and input-voltage derating curves Cooling Free-air convection; no fan Working humidity 20 ~ 90% RH non-condensing Storage temperature / humidity -40 ~ +85°C, 10 ~ 95% RH non-condensing Temperature coefficient ±0.03%/°C (0 ~ 50°C) Operating altitude Up to 5,000 m as stated for this series; the applicable overvoltage category and temperature derating impose additional limits. Overvoltage category Category III up to 2,000 m under the standards specified in this series datasheet. This is an insulation category, separate from the output-overvoltage protection threshold. Higher-altitude temperature derating For operation above 2,000 m, reduce the permitted ambient temperature by 5 °C per additional 1,000 m. Verify the applicable insulation/approval limits for the installation. Full rated output is not available at every point within the temperature and input ranges. Use the ambient-temperature and static input-voltage curves on PDF page 3 for this model and installation orientation. Dimensions and Installation Overall dimensions (L × W × H) 99 × 82 × 30 mm Case number 239A Drawing tolerance ±1 mm Mounting-hole callouts 2-M3 L=3.0; 2-M3 L=5 Terminal 1 AC/L Terminal 2 AC/N Terminal 3 FG (protective earth) Terminal 4 DC OUTPUT -V Terminal 5 DC OUTPUT +V Use the mechanical drawing on PDF page 4 to locate the holes and confirm the permitted screw penetration for the selected mounting face. The M3/M4 callouts are mounting dimensions, not accessory ordering codes. Match wiring, protective-earth connection and output polarity to the terminal markings. Keep ventilation openings clear for convection cooling. This enclosed supply is a component for installation inside final equipment. Complete installation and electrical work using the manufacturer’s installation instructions and the applicable equipment requirements. Reference Weight Catalog reference per unit 210 g This value is the per-unit reference in the manufacturer’s PACKING row. It is not a measured net weight or a quotation for the complete shipping package. Application and Datasheet Notes EMC results are for a component installed on the manufacturer’s specified test plate. The finished equipment must be checked again for EMC compliance. Safety approvals and regional exceptions depend on the exact model and datasheet revision; refer to the linked specification and applicable certificates when selecting the unit. Additional Manufacturer Data Vibration test 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes MTBF reference 3201.5K hrs min. Telcordia SR-332 (Bellcore) ; 655.5Khrs min. MIL-HDBK-217F (25°C) Dielectric withstand I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC Power indication LED power-on indicator Manufacturer datasheet warranty 3 years; subject to the manufacturer’s applicable warranty terms MTBF is a reliability prediction under the stated method and conditions, not a service-life or warranty-duration guarantee. Source: MEAN WELL LRS-35 datasheet, revision 2025-04-07, in the linked LRS catalog. Use the exact model specification, notes and drawings together when selecting and installing this supply.

  Read more less

  $24.15

  View options

• 

  View options

  MEAN WELL LRS-35 series: enclosed AC/DC switching power supply - LRS-35-24

  MEAN WELL LRS-35-24 is a single-output enclosed switching power supply with a 24 V DC output, 1.5 A rated current and 36 W rated output power. Universal AC input / full range. Free-air convection; no fan. Download MEAN WELL LRS-35 Datasheet (PDF) The combined LRS catalog includes this series on PDF pages 1–4. Specifications: page 2; mechanical drawing: page 4. Model and Output Specifications Complete model LRS-35-24 Series LRS-35 Output-voltage code 24 = 24 V DC nominal output Rated output voltage 24 V DC Rated output current 1.5 A Output current range 0 to 1.5 A Rated output power 36 W Output voltage adjustment 21.6 to 28.8 V Ripple and noise, maximum 150 mVp-p Voltage tolerance ±1.0% Line regulation ±0.5% Load regulation ±0.5% Efficiency, typical 88% at the stated test conditions 230 VAC input, rated load, 25°C ambient unless otherwise stated. Ripple/noise test: 20 MHz bandwidth; 12-inch twisted-pair wire terminated with 0.1 µF and 47 µF parallel capacitors. Voltage tolerance includes setup tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load; load regulation is measured from 0% to 100% rated load. Input and Timing AC input range 85 to 264 VAC Input range selection Universal AC input / full range DC input range 120 to 373 VDC Input frequency 47 to 63 Hz AC input current, typical 0.7A/115VAC 0.42A/230VAC Inrush current, typical Cold start 45A/230VAC Leakage current <0.75mA / 240VAC Setup / rise time 1000 / 30 ms at 230 VAC; 2000 / 30 ms at 115 VAC, full load Hold-up time, typical 30 ms at 230 VAC; 12 ms at 115 VAC, full load Transient input withstand 300 VAC for 5 seconds; this is a surge condition, not the continuous input rating Full load; setup at cold first start. Rapid on/off cycling can increase setup time. Protection and Recovery Short-circuit protection Included Overload 110 to 150% of rated output power. Hiccup; automatically recovers after fault condition is removed. Overvoltage protection 28.8 to 33.6 V. Shut down output; re-power on to recover. Environment and Cooling Ambient operating temperature -30 to 70 °C; apply the temperature and input-voltage derating curves Cooling Free-air convection; no fan Working humidity 20 ~ 90% RH non-condensing Storage temperature / humidity -40 ~ +85°C, 10 ~ 95% RH non-condensing Temperature coefficient ±0.03%/°C (0 ~ 50°C) Operating altitude Up to 5,000 m as stated for this series; the applicable overvoltage category and temperature derating impose additional limits. Overvoltage category Category III up to 2,000 m under the standards specified in this series datasheet. This is an insulation category, separate from the output-overvoltage protection threshold. Higher-altitude temperature derating For operation above 2,000 m, reduce the permitted ambient temperature by 5 °C per additional 1,000 m. Verify the applicable insulation/approval limits for the installation. Full rated output is not available at every point within the temperature and input ranges. Use the ambient-temperature and static input-voltage curves on PDF page 3 for this model and installation orientation. Dimensions and Installation Overall dimensions (L × W × H) 99 × 82 × 30 mm Case number 239A Drawing tolerance ±1 mm Mounting-hole callouts 2-M3 L=3.0; 2-M3 L=5 Terminal 1 AC/L Terminal 2 AC/N Terminal 3 FG (protective earth) Terminal 4 DC OUTPUT -V Terminal 5 DC OUTPUT +V Use the mechanical drawing on PDF page 4 to locate the holes and confirm the permitted screw penetration for the selected mounting face. The M3/M4 callouts are mounting dimensions, not accessory ordering codes. Match wiring, protective-earth connection and output polarity to the terminal markings. Keep ventilation openings clear for convection cooling. This enclosed supply is a component for installation inside final equipment. Complete installation and electrical work using the manufacturer’s installation instructions and the applicable equipment requirements. Reference Weight Catalog reference per unit 210 g This value is the per-unit reference in the manufacturer’s PACKING row. It is not a measured net weight or a quotation for the complete shipping package. Application and Datasheet Notes EMC results are for a component installed on the manufacturer’s specified test plate. The finished equipment must be checked again for EMC compliance. Safety approvals and regional exceptions depend on the exact model and datasheet revision; refer to the linked specification and applicable certificates when selecting the unit. Additional Manufacturer Data Vibration test 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes MTBF reference 3201.5K hrs min. Telcordia SR-332 (Bellcore) ; 655.5Khrs min. MIL-HDBK-217F (25°C) Dielectric withstand I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC Power indication LED power-on indicator Manufacturer datasheet warranty 3 years; subject to the manufacturer’s applicable warranty terms MTBF is a reliability prediction under the stated method and conditions, not a service-life or warranty-duration guarantee. Source: MEAN WELL LRS-35 datasheet, revision 2025-04-07, in the linked LRS catalog. Use the exact model specification, notes and drawings together when selecting and installing this supply.

  Read more less

  $21.69

  View options

• 

  View options

  MEAN WELL LRS-35 series: enclosed AC/DC switching power supply - LRS-35-15

  MEAN WELL LRS-35-15 is a single-output enclosed switching power supply with a 15 V DC output, 2.4 A rated current and 36 W rated output power. Universal AC input / full range. Free-air convection; no fan. Download MEAN WELL LRS-35 Datasheet (PDF) The combined LRS catalog includes this series on PDF pages 1–4. Specifications: page 2; mechanical drawing: page 4. Model and Output Specifications Complete model LRS-35-15 Series LRS-35 Output-voltage code 15 = 15 V DC nominal output Rated output voltage 15 V DC Rated output current 2.4 A Output current range 0 to 2.4 A Rated output power 36 W Output voltage adjustment 13.5 to 18 V Ripple and noise, maximum 120 mVp-p Voltage tolerance ±1.0% Line regulation ±0.5% Load regulation ±0.5% Efficiency, typical 86% at the stated test conditions 230 VAC input, rated load, 25°C ambient unless otherwise stated. Ripple/noise test: 20 MHz bandwidth; 12-inch twisted-pair wire terminated with 0.1 µF and 47 µF parallel capacitors. Voltage tolerance includes setup tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load; load regulation is measured from 0% to 100% rated load. Input and Timing AC input range 85 to 264 VAC Input range selection Universal AC input / full range DC input range 120 to 373 VDC Input frequency 47 to 63 Hz AC input current, typical 0.7A/115VAC 0.42A/230VAC Inrush current, typical Cold start 45A/230VAC Leakage current <0.75mA / 240VAC Setup / rise time 1000 / 30 ms at 230 VAC; 2000 / 30 ms at 115 VAC, full load Hold-up time, typical 30 ms at 230 VAC; 12 ms at 115 VAC, full load Transient input withstand 300 VAC for 5 seconds; this is a surge condition, not the continuous input rating Full load; setup at cold first start. Rapid on/off cycling can increase setup time. Protection and Recovery Short-circuit protection Included Overload 110 to 150% of rated output power. Hiccup; automatically recovers after fault condition is removed. Overvoltage protection 18.75 to 21.75 V. Shut down output; re-power on to recover. Environment and Cooling Ambient operating temperature -30 to 70 °C; apply the temperature and input-voltage derating curves Cooling Free-air convection; no fan Working humidity 20 ~ 90% RH non-condensing Storage temperature / humidity -40 ~ +85°C, 10 ~ 95% RH non-condensing Temperature coefficient ±0.03%/°C (0 ~ 50°C) Operating altitude Up to 5,000 m as stated for this series; the applicable overvoltage category and temperature derating impose additional limits. Overvoltage category Category III up to 2,000 m under the standards specified in this series datasheet. This is an insulation category, separate from the output-overvoltage protection threshold. Higher-altitude temperature derating For operation above 2,000 m, reduce the permitted ambient temperature by 5 °C per additional 1,000 m. Verify the applicable insulation/approval limits for the installation. Full rated output is not available at every point within the temperature and input ranges. Use the ambient-temperature and static input-voltage curves on PDF page 3 for this model and installation orientation. Dimensions and Installation Overall dimensions (L × W × H) 99 × 82 × 30 mm Case number 239A Drawing tolerance ±1 mm Mounting-hole callouts 2-M3 L=3.0; 2-M3 L=5 Terminal 1 AC/L Terminal 2 AC/N Terminal 3 FG (protective earth) Terminal 4 DC OUTPUT -V Terminal 5 DC OUTPUT +V Use the mechanical drawing on PDF page 4 to locate the holes and confirm the permitted screw penetration for the selected mounting face. The M3/M4 callouts are mounting dimensions, not accessory ordering codes. Match wiring, protective-earth connection and output polarity to the terminal markings. Keep ventilation openings clear for convection cooling. This enclosed supply is a component for installation inside final equipment. Complete installation and electrical work using the manufacturer’s installation instructions and the applicable equipment requirements. Reference Weight Catalog reference per unit 210 g This value is the per-unit reference in the manufacturer’s PACKING row. It is not a measured net weight or a quotation for the complete shipping package. Application and Datasheet Notes EMC results are for a component installed on the manufacturer’s specified test plate. The finished equipment must be checked again for EMC compliance. Safety approvals and regional exceptions depend on the exact model and datasheet revision; refer to the linked specification and applicable certificates when selecting the unit. Additional Manufacturer Data Vibration test 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes MTBF reference 3201.5K hrs min. Telcordia SR-332 (Bellcore) ; 655.5Khrs min. MIL-HDBK-217F (25°C) Dielectric withstand I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC Power indication LED power-on indicator Manufacturer datasheet warranty 3 years; subject to the manufacturer’s applicable warranty terms MTBF is a reliability prediction under the stated method and conditions, not a service-life or warranty-duration guarantee. Source: MEAN WELL LRS-35 datasheet, revision 2025-04-07, in the linked LRS catalog. Use the exact model specification, notes and drawings together when selecting and installing this supply.

  Read more less

  $23.66

  View options

• 

  View options

  MEAN WELL LRS-35 series: enclosed AC/DC switching power supply - LRS-35-5

  MEAN WELL LRS-35-5 is a single-output enclosed switching power supply with a 5 V DC output, 7 A rated current and 35 W rated output power. Universal AC input / full range. Free-air convection; no fan. Download MEAN WELL LRS-35 Datasheet (PDF) The combined LRS catalog includes this series on PDF pages 1–4. Specifications: page 2; mechanical drawing: page 4. Model and Output Specifications Complete model LRS-35-5 Series LRS-35 Output-voltage code 5 = 5 V DC nominal output Rated output voltage 5 V DC Rated output current 7 A Output current range 0 to 7 A Rated output power 35 W Output voltage adjustment 4.5 to 5.5 V Ripple and noise, maximum 80 mVp-p Voltage tolerance ±2.0% Line regulation ±0.5% Load regulation ±1.0% Efficiency, typical 82% at the stated test conditions 230 VAC input, rated load, 25°C ambient unless otherwise stated. Ripple/noise test: 20 MHz bandwidth; 12-inch twisted-pair wire terminated with 0.1 µF and 47 µF parallel capacitors. Voltage tolerance includes setup tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load; load regulation is measured from 0% to 100% rated load. At 0–50% load, burst-mode operation on this output-voltage version may cause ripple and noise to exceed the specified value. Input and Timing AC input range 85 to 264 VAC Input range selection Universal AC input / full range DC input range 120 to 373 VDC Input frequency 47 to 63 Hz AC input current, typical 0.7A/115VAC 0.42A/230VAC Inrush current, typical Cold start 45A/230VAC Leakage current <0.75mA / 240VAC Setup / rise time 1000 / 30 ms at 230 VAC; 2000 / 30 ms at 115 VAC, full load Hold-up time, typical 30 ms at 230 VAC; 12 ms at 115 VAC, full load Transient input withstand 300 VAC for 5 seconds; this is a surge condition, not the continuous input rating Full load; setup at cold first start. Rapid on/off cycling can increase setup time. Protection and Recovery Short-circuit protection Included Overload 110 to 150% of rated output power. Hiccup; automatically recovers after fault condition is removed. Overvoltage protection 5.75 to 6.9 V. Shut down output; re-power on to recover. Environment and Cooling Ambient operating temperature -30 to 70 °C; apply the temperature and input-voltage derating curves Cooling Free-air convection; no fan Working humidity 20 ~ 90% RH non-condensing Storage temperature / humidity -40 ~ +85°C, 10 ~ 95% RH non-condensing Temperature coefficient ±0.03%/°C (0 ~ 50°C) Operating altitude Up to 5,000 m as stated for this series; the applicable overvoltage category and temperature derating impose additional limits. Overvoltage category Category III up to 2,000 m under the standards specified in this series datasheet. This is an insulation category, separate from the output-overvoltage protection threshold. Higher-altitude temperature derating For operation above 2,000 m, reduce the permitted ambient temperature by 5 °C per additional 1,000 m. Verify the applicable insulation/approval limits for the installation. Full rated output is not available at every point within the temperature and input ranges. Use the ambient-temperature and static input-voltage curves on PDF page 3 for this model and installation orientation. Dimensions and Installation Overall dimensions (L × W × H) 99 × 82 × 30 mm Case number 239A Drawing tolerance ±1 mm Mounting-hole callouts 2-M3 L=3.0; 2-M3 L=5 Terminal 1 AC/L Terminal 2 AC/N Terminal 3 FG (protective earth) Terminal 4 DC OUTPUT -V Terminal 5 DC OUTPUT +V Use the mechanical drawing on PDF page 4 to locate the holes and confirm the permitted screw penetration for the selected mounting face. The M3/M4 callouts are mounting dimensions, not accessory ordering codes. Match wiring, protective-earth connection and output polarity to the terminal markings. Keep ventilation openings clear for convection cooling. This enclosed supply is a component for installation inside final equipment. Complete installation and electrical work using the manufacturer’s installation instructions and the applicable equipment requirements. Reference Weight Catalog reference per unit 210 g This value is the per-unit reference in the manufacturer’s PACKING row. It is not a measured net weight or a quotation for the complete shipping package. Application and Datasheet Notes EMC results are for a component installed on the manufacturer’s specified test plate. The finished equipment must be checked again for EMC compliance. Safety approvals and regional exceptions depend on the exact model and datasheet revision; refer to the linked specification and applicable certificates when selecting the unit. Additional Manufacturer Data Vibration test 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes MTBF reference 3201.5K hrs min. Telcordia SR-332 (Bellcore) ; 655.5Khrs min. MIL-HDBK-217F (25°C) Dielectric withstand I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC Power indication LED power-on indicator Manufacturer datasheet warranty 3 years; subject to the manufacturer’s applicable warranty terms MTBF is a reliability prediction under the stated method and conditions, not a service-life or warranty-duration guarantee. Source: MEAN WELL LRS-35 datasheet, revision 2025-04-07, in the linked LRS catalog. Use the exact model specification, notes and drawings together when selecting and installing this supply.

  Read more less

  $25.14

  View options

Back to top