• 

  View options

  MEAN WELL GST60A series: Desktop AC/DC Power Adapter - GST60A12-P1J

  MEAN WELL GST60A12-P1J supplies 12 VDC at up to 5 A, with a 60 W maximum catalogue output rating. This Class I desktop adapter uses an IEC320-C14 three-pole AC inlet and a P1J center-positive DC plug. Apply the input and ambient derating limits below. Product Datasheet Download MEAN WELL GST60A Datasheet (PDF) The GST60A section is on PDF pages 61, 62, 63, 64, 65. Refer to the complete mechanical drawings and notes when planning installation. Model and Output Complete model GST60A12-P1J. Series and format GST60A single-output desktop AC/DC adapter; Class I with FG. Output voltage 12 VDC. Rated current / operating range 5 A rated; 0–5 A range. Rated output power, maximum 60 W, subject to input and temperature derating. Ripple and noise, maximum 120 mVp-p. Voltage tolerance / load regulation ±3.0% / ±3.0%. Line regulation ±1.0%. Efficiency, typical 89.5%. Model code GST60A identifies the series and AC-input format; 12 identifies the 12 V output; P1J identifies the standard DC plug. Choose the load to stay within the voltage, current and maximum-power ratings together. The output-voltage setting is measured at the DC plug terminal with 50% load. Input, Timing and Energy AC input 90–264 VAC; 47–63 Hz. AC connection IEC320-C14 three-pole AC inlet. Input current, typical 1.4 A at 115 VAC; 1 A at 230 VAC. Cold-start inrush, maximum 35 A at 115 VAC; 65 A at 230 VAC. Leakage current, maximum 0.75 mA at 240 VAC. Start-up and hold-up At full load: set-up 1000 ms and rise 50 ms at both 230 VAC and 115 VAC; typical hold-up 50 ms at 230 VAC and 15 ms at 115 VAC. No-load power consumption <0.075 W. Energy efficiency Level VI; EISA 2007/DoE, NRCan, Korea K-MEPS, AU/NZ MEPS, EU ErP and CoC Version 5. Set-up time is measured from the first cold start. Rapid power cycling may increase the set-up time. Select a suitable mains lead for the C14 inlet and the local outlet. Confirm AC-cord supply with the order; the series datasheet does not specify a supplied mains lead. Protection Short circuit / overload 105–150% of rated output power; hiccup mode with automatic recovery after removal of the fault. Overvoltage 12.6–16.2 V; output shutdown, re-power to recover. Overtemperature Output shutdown; re-power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curve. Temperature derating Horizontal installation: full load from −30°C through 50°C, falling to 50% at 70°C. Input-voltage curve, 60 Hz 90% load at 90 VAC, rising to 100% at 100 VAC and remaining at 100% through 264 VAC. Operating humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–50°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle and 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce allowable ambient by 3.5°C per 1000 m for fanless models, or 5°C per 1000 m for fan-cooled models. Use the temperature and input-voltage limits together. Allow unobstructed heat dissipation around the enclosure; lower input voltage or higher ambient can reduce available output. Mechanical Details and Standard Connections Body dimensions, L × W × H 125 × 50 × 31.5 mm. Enclosure Fully enclosed 94V-0 flame-retardant plastic case; power-on LED indicator. DC output cable UL1185, 16 AWG; 1000 ±50 mm. Standard DC plug P1J tuning-fork type; 5.5 mm outside diameter, 2.1 mm inside diameter, 11 ±0.5 mm insertion length. DC polarity Center positive (C+); outer contact negative. Catalogue single-unit weight 305 g from the explicit single-unit PACKING entry; this is a catalogue reference rather than a measured shipping weight. Packing 40 pieces / 13.02 kg / 1.04 CUFT. Output and protective earth The DC negative output is not connected to AC FG. Use the protective-earth connection provided by the three-pole mains inlet. Check the complete mechanical drawing for plug orientation, cable routing and local clearances. Optional DC Connections and Accessories Optional DC-plug customization of the standard cable is subject to a minimum order quantity. Quick-adapter accessories are sold separately without a minimum order quantity. Match voltage, polarity, dimensions and current rating before selecting a connector; an accessory current rating does not increase the adapter output rating. Dimensions below are outside diameter / inside diameter / insertion length in millimetres. Optional tuning-fork types: P1I 5.5 / 2.1 / 9.5 mm; P1L 5.5 / 2.5 / 9.5 mm; P1M 5.5 / 2.5 / 11 mm; P1IR 5.5 / 2.1 / 9.5 mm; P1JR 5.5 / 2.1 / 11 mm; P1LR 5.5 / 2.5 / 9.5 mm; P1MR 5.5 / 2.5 / 11 mm. Types ending in R are right-angled. Quick adapters are listed for the optional tuning-fork types above, each rated 7.5 A maximum. Barrel-style cable options: P2I 5.5 / 2.1 / 9.5 mm; P2J 5.5 / 2.1 / 11 mm; P2L 5.5 / 2.5 / 9.5 mm; P2M 5.5 / 2.5 / 11 mm; P2IR 5.5 / 2.1 / 9.5 mm; P2JR 5.5 / 2.1 / 11 mm; P2LR 5.5 / 2.5 / 9.5 mm; P2MR 5.5 / 2.5 / 11 mm. No quick adapter is listed for these barrel types. Locking cable options, SWITCHCRAFT original or equivalent: P2S(S761K) 5.53 / 2.03 / 12.06 mm; P2K(761K) 5.53 / 2.54 / 12.06 mm; P2C(S760K) 5.53 / 2.03 / 9.52 mm; P2D(760K) 5.53 / 2.54 / 9.52 mm. No quick adapter is listed for these locking types. Mini-pin cable options, EIAJ equivalent: P3A 2.35 / 0.7 / 11 mm; P3B 4 / 1.7 / 11 mm; P3C 4.75 / 1.7 / 11 mm. Quick adapters are available, rated 5 A maximum. Center-pin cable options, EIAJ equivalent (outside / inside / insertion / center-pin diameter): P4A 5.5 / 3.4 / 11 / 1.0 mm; P4B 6.5 / 4.4 / 11 / 1.4 mm; P4C 7.4 / 5.1 / 11 / 0.6 mm. Quick adapters are available, rated 7.5 A maximum. R6B: Locking mini-DIN 3-pin male; KYCON KPPX-3P equivalent. Pins: 1 +Vo; 2 −Vo; 3 +Vo. Quick adapter available, 7.5 A maximum. R7B: Locking mini-DIN 4-pin male; KYCON KPPX-4P equivalent. Pins: 1 +Vo; 2 −Vo; 3 −Vo; 4 +Vo. Quick adapter available, 7.5 A maximum. R7BF: Locking mini-DIN 4-pin female; KYCON KPJX-CM-4S equivalent. Pins: 1 +Vo; 2 −Vo; 3 −Vo; 4 +Vo. No quick adapter is listed for this type. R1B: DIN 5-pin male. Pins: 1 −Vo; 2 −Vo; 3 +Vo; 4 −Vo; 5 +Vo. Quick adapter available, 7.5 A maximum. Stripped and tinned leads are available by customer request: lead 1 +Vo and lead 2 −Vo. Standard illustrated lengths are L = 25 mm and L1 = 5 mm; other lengths are by request. Red/black colours in the drawing are references only; follow the actual product. No quick adapter is listed for this lead option. Safety and EMC Safety standards listed UL62368-1; CSA C22.2 No.62368-1; TUV BS EN/EN62368-1; BSMI CNS15598-1; CCC GB4943.1; AS/NZS62368.1; PSE J62368-1; BIS IS13252; KC K60950-1; EAC TP TC004. Withstand voltage Input/output 3 kVAC; input/FG 2 kVAC; output/FG 0.5 kVAC. Insulation resistance Input/output, input/FG and output/FG: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22, CAN ICES-3(B) / NMB-3(B), CNS15936, GB17625.1, EAC TP TC020 and MSIP KN32: Class B conducted and radiated emissions. Limited power source The series is listed as passing LPS requirements. Harmonic current BS EN/EN61000-3-2 and GB9254: Class A. Voltage flicker BS EN/EN61000-3-3. Immunity: BS EN/EN55035. IEC/EN61000-4-2 ESD: level 4, 15 kV air and 8 kV contact. -4-3 RF: level 2, 3 V/m; -4-4 EFT: level 2, 1 kV; -4-5 surge: level 3, 1 kV line-to-line and 2 kV line-to-FG. -4-6 conducted susceptibility: level 2, 3 V; -4-8 magnetic field: level 2, 3 A/m. -4-11: >95% dip for 0.5 periods, 30% dip for 25 periods and >95% interruption for 250 periods. The adapter is considered an independent unit. Reconfirm whole-system EMC compliance in the final equipment with its actual cable and installation. Reliability and Measurement Notes MTBF, minimum estimates 3620.0 thousand hours, Telcordia SR-332 (Bellcore); 709.7 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision GST60A-SPEC, 2026-04-03; combined PDF pages 61–65. Unless otherwise stated, parameters are specified at 230 VAC input, rated load, 25°C and 70% RH. Ripple and noise are measured with 20 MHz bandwidth, a 12-inch twisted pair and parallel 0.1 µF and 47 µF capacitors. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low line to high line at rated load.

  Read more less

  $39.92

  View options

• 

  View options

  MEAN WELL GST36U series: Wall-Plug AC/DC Power Adapter - GST36U12-P1J

  MEAN WELL GST36U12-P1J supplies 12 VDC at up to 3 A, with a 36 W maximum catalogue output rating. This Class II wall-plug adapter uses an integrated US-style two-pin AC plug and a P1J center-positive DC plug. Apply the input and ambient derating limits below. Product Datasheet Download MEAN WELL GST36U Datasheet (PDF) The GST36U section is on PDF pages 51, 52, 53, 54, 55. Refer to the complete mechanical drawings and notes when planning installation. Model and Output Complete model GST36U12-P1J. Series and format GST36U single-output wall-plug AC/DC adapter; Class II without FG. Output voltage 12 VDC. Rated current / operating range 3 A rated; 0–3 A range. Rated output power, maximum 36 W, subject to input and temperature derating. Ripple and noise, maximum 100 mVp-p. Voltage tolerance / load regulation ±3.0% / ±3.0%. Line regulation ±1.0%. Efficiency, typical 87.5%. Model code GST36U identifies the series and AC-input format; 12 identifies the 12 V output; P1J identifies the standard DC plug. Choose the load to stay within the voltage, current and maximum-power ratings together. The output-voltage setting is measured at the DC plug terminal with 50% load. Input, Timing and Energy AC input 85–264 VAC; 47–63 Hz. AC connection Integrated US-style two-pin AC plug. Input current 0.8 A at 115 VAC; 0.45 A at 230 VAC. Cold-start inrush, maximum 35 A at 115 VAC; 70 A at 230 VAC. Leakage current, maximum 0.25 mA at 240 VAC. Start-up and hold-up At full load: 230 VAC, 1000 / 30 / 50 ms; 115 VAC, 1500 / 30 / 13 ms (set-up / rise / hold-up). No-load power consumption <0.075 W. Energy efficiency Level VI; EISA 2007/DoE and NRCan. The two-pin mains plug is integral to the adapter. Match its physical plug format to the installation outlet; the wide electrical input range does not change that plug format. Protection Short circuit / overload 110–150% of rated output power; hiccup mode with automatic recovery after removal of the fault. Overvoltage 110–140% of rated output voltage; zener-diode clamp. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curve. Temperature derating Full load through 50°C, falling to 50% at 70°C. Operation in the −30 to −20°C portion is specified for 230 VAC input only. Input-voltage curve, 60 Hz 85% load at 85 VAC, rising to 100% at 100 VAC and remaining at 100% through 264 VAC. Operating humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–50°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle and 60 minutes along each X, Y and Z axis. Use the temperature and input-voltage limits together. Allow unobstructed heat dissipation around the enclosure; lower input voltage or higher ambient can reduce available output. Mechanical Details and Standard Connections Body dimensions, L × W × H 79 × 54 × 33 mm. Enclosure Fully enclosed 94V-0 flame-retardant plastic case; power-on LED indicator. DC output cable UL2468, 16 AWG; 1000 ±50 mm. Standard DC plug P1J tuning-fork type; 5.5 mm outside diameter, 2.1 mm inside diameter, 11 ±0.5 mm insertion length. DC polarity Center positive (C+); outer contact negative. Catalogue single-unit weight 204.5 g from the explicit single-unit PACKING entry; this is a catalogue reference rather than a measured shipping weight. Packing 60 pieces / 13.3 kg / 1.15 CUFT. Mains-pin projection The mechanical drawing separately marks 17 mm for the projecting AC-plug portion; use the full drawing for socket clearance. Check the complete mechanical drawing for plug orientation, cable routing and local clearances. Optional DC Connections and Accessories Optional DC-plug customization of the standard cable is subject to a minimum order quantity. Quick-adapter accessories are sold separately without a minimum order quantity. Match voltage, polarity, dimensions and current rating before selecting a connector; an accessory current rating does not increase the adapter output rating. Dimensions below are outside diameter / inside diameter / insertion length in millimetres. Optional tuning-fork types: P1I 5.5 / 2.1 / 9.5 mm; P1L 5.5 / 2.5 / 9.5 mm; P1M 5.5 / 2.5 / 11 mm; P1IR 5.5 / 2.1 / 9.5 mm; P1JR 5.5 / 2.1 / 11 mm; P1LR 5.5 / 2.5 / 9.5 mm; P1MR 5.5 / 2.5 / 11 mm. Types ending in R are right-angled. Quick adapters are listed for the optional tuning-fork types above, each rated 7.5 A maximum. Barrel-style cable options: P2I 5.5 / 2.1 / 9.5 mm; P2J 5.5 / 2.1 / 11 mm; P2L 5.5 / 2.5 / 9.5 mm; P2M 5.5 / 2.5 / 11 mm; P2IR 5.5 / 2.1 / 9.5 mm; P2JR 5.5 / 2.1 / 11 mm; P2LR 5.5 / 2.5 / 9.5 mm; P2MR 5.5 / 2.5 / 11 mm. No quick adapter is listed for these barrel types. Locking cable options, SWITCHCRAFT original or equivalent: P2S(S761K) 5.53 / 2.03 / 12.06 mm; P2K(761K) 5.53 / 2.54 / 12.06 mm; P2C(S760K) 5.53 / 2.03 / 9.52 mm; P2D(760K) 5.53 / 2.54 / 9.52 mm. No quick adapter is listed for these locking types. Mini-pin cable options, EIAJ equivalent: P3A 2.35 / 0.7 / 11 mm; P3B 4 / 1.7 / 11 mm; P3C 4.75 / 1.7 / 11 mm. Quick adapters are available, rated 5 A maximum. Center-pin cable options, EIAJ equivalent (outside / inside / insertion / center-pin diameter): P4A 5.5 / 3.4 / 11 / 1.0 mm; P4B 6.5 / 4.4 / 11 / 1.4 mm; P4C 7.4 / 5.1 / 11 / 0.6 mm. Quick adapters are available, rated 7.5 A maximum. R6B: Locking mini-DIN 3-pin male; KYCON KPPX-3P equivalent. Pins: 1 +Vo; 2 −Vo; 3 +Vo. Quick adapter available, 7.5 A maximum. R7B: Locking mini-DIN 4-pin male; KYCON KPPX-4P equivalent. Pins: 1 +Vo; 2 −Vo; 3 −Vo; 4 +Vo. Quick adapter available, 7.5 A maximum. R7BF: Locking mini-DIN 4-pin female; KYCON KPJX-CM-4S equivalent. Pins: 1 +Vo; 2 −Vo; 3 −Vo; 4 +Vo. No quick adapter is listed for this type. R1B: DIN 5-pin male. Pins: 1 −Vo; 2 −Vo; 3 +Vo; 4 −Vo; 5 +Vo. Quick adapter available, 7.5 A maximum. Stripped and tinned leads are available by customer request: lead 1 +Vo and lead 2 −Vo. Standard illustrated lengths are L = 25 mm and L1 = 5 mm; other lengths are by request. Red/black colours in the drawing are references only; follow the actual product. No quick adapter is listed for this lead option. Safety and EMC Safety standards listed UL62368-1, CSA C22.2 No.62368-1, BSMI CNS15598-1 and EAC TP TC004 approved. Withstand voltage Input/output: 4242 VDC. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions FCC Part 15 / CISPR22, CAN ICES-3(B) / NMB-3(B), CNS15936 and EAC TP TC020: Class B conducted and radiated emissions. Limited power source The series is listed as passing LPS requirements. The adapter is considered an independent unit. Reconfirm whole-system EMC compliance in the final equipment with its actual cable and installation. Reliability and Measurement Notes MTBF, minimum estimates 3838.3 thousand hours, Telcordia SR-332 (Bellcore); 557.9 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision GST36U-SPEC, 2026-04-03; combined PDF pages 51–55. Unless otherwise stated, parameters are specified at 115 VAC input, rated load, 25°C and 70% RH. Ripple and noise are measured with 20 MHz bandwidth, a 12-inch twisted pair and parallel 0.1 µF and 47 µF capacitors. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low line to high line at rated load. Load regulation is measured from 10% to 100% rated load.

  Read more less

  $31.05

  View options

• 

  View options

  MEAN WELL GST360B series: Desktop AC/DC Power Adapter - GST360B55-C6P

  MEAN WELL GST360B55-C6P is a single-output desktop AC/DC power adapter rated at 55 VDC, 6.55 A and 360 W. It has a C6P DC output plug and a 2-pole IEC320-C18 inlet with Class II insulation. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST360B Datasheet (PDF) The GST360B section is on PDF pages 94, 95, 96, 97. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST360B55-C6P. Series GST360B industrial desktop adapter. Input construction Class II; 2-pole IEC320-C18, without FG. DC termination Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 55 VDC. Rated current 6.55 A. Output current range 0–6.55 A. Rated output power, maximum 360 W. Ripple and noise, maximum 200 mVp-p. Voltage tolerance ±2.0%. Line regulation ±1.0%. Load regulation ±2.0%. Efficiency, typical 95% for this C6P version. Peak power 450 W for 3 seconds. This is a short-duration peak, not a continuous-output rating. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3.8 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 8 ms at both 230 VAC and 115 VAC, at full load. Touch current <0.5 mA at 260 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 135–155% of rated output power. Output shutdown; reapply input power to recover. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load from −30 to 35°C, then 80% at 50°C, 65% at 60°C and 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 85% at 100 VAC; the graph holds 85% up to the 120 VAC transition, with 100% from 120 to 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–35°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Operating altitude Up to 5000 m, with altitude and temperature derating. Overvoltage category OVC II under UL62368-1 and BS EN/EN62368-1, up to 5000 m. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug C6P: Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Grounding Class II, without FG; no protective-earth contact in the 2-pole inlet. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Optional DC Terminations MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. These are alternative output terminations available by request, not included mating accessories. MIC4 and C4P are listed for 36–55 V versions. Confirm the required option and its current rating before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, Dekra BS EN/EN62368-1, IEC 61558-1, IEC 61558-2-16, CCC GB4943.1, AS/NZS 61558-1/-2-16 and EAC TP TC 004. Energy-saving compliance USA EISA 2007/DoE and Canada NRCan. Withstand voltage Input/output: 3 kVAC. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Harmonic current / flicker BS EN/EN61000-3-2 Class A; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1400 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.4 kg per unit; 8 pieces / 12 kg / 0.82 CUFT. MTBF, minimum estimates 2057.2 thousand hours, Telcordia SR-332 (Bellcore); 265.9 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 94–97.

  Read more less

  $238.54

  View options

• 

  View options

  MEAN WELL GST360B series: Desktop AC/DC Power Adapter - GST360B48-C6P

  MEAN WELL GST360B48-C6P is a single-output desktop AC/DC power adapter rated at 48 VDC, 7.5 A and 360 W. It has a C6P DC output plug and a 2-pole IEC320-C18 inlet with Class II insulation. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST360B Datasheet (PDF) The GST360B section is on PDF pages 94, 95, 96, 97. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST360B48-C6P. Series GST360B industrial desktop adapter. Input construction Class II; 2-pole IEC320-C18, without FG. DC termination Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 48 VDC. Rated current 7.5 A. Output current range 0–7.5 A. Rated output power, maximum 360 W. Ripple and noise, maximum 200 mVp-p. Voltage tolerance ±2.0%. Line regulation ±1.0%. Load regulation ±2.0%. Efficiency, typical 95% for this C6P version. Peak power 450 W for 3 seconds. This is a short-duration peak, not a continuous-output rating. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3.8 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 8 ms at both 230 VAC and 115 VAC, at full load. Touch current <0.5 mA at 260 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 135–155% of rated output power. Output shutdown; reapply input power to recover. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load from −30 to 35°C, then 80% at 50°C, 65% at 60°C and 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 85% at 100 VAC; the graph holds 85% up to the 120 VAC transition, with 100% from 120 to 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–35°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Operating altitude Up to 5000 m, with altitude and temperature derating. Overvoltage category OVC II under UL62368-1 and BS EN/EN62368-1, up to 5000 m. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug C6P: Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Grounding Class II, without FG; no protective-earth contact in the 2-pole inlet. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Optional DC Terminations MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. These are alternative output terminations available by request, not included mating accessories. MIC4 and C4P are listed for 36–55 V versions. Confirm the required option and its current rating before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, Dekra BS EN/EN62368-1, IEC 61558-1, IEC 61558-2-16, CCC GB4943.1, AS/NZS 61558-1/-2-16 and EAC TP TC 004. Energy-saving compliance USA EISA 2007/DoE and Canada NRCan. Withstand voltage Input/output: 3 kVAC. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Harmonic current / flicker BS EN/EN61000-3-2 Class A; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1400 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.4 kg per unit; 8 pieces / 12 kg / 0.82 CUFT. MTBF, minimum estimates 2057.2 thousand hours, Telcordia SR-332 (Bellcore); 265.9 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 94–97.

  Read more less

  $238.54

  View options

• 

  View options

  MEAN WELL GST360B series: Desktop AC/DC Power Adapter - GST360B36-C6P

  MEAN WELL GST360B36-C6P is a single-output desktop AC/DC power adapter rated at 36 VDC, 10 A and 360 W. It has a C6P DC output plug and a 2-pole IEC320-C18 inlet with Class II insulation. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST360B Datasheet (PDF) The GST360B section is on PDF pages 94, 95, 96, 97. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST360B36-C6P. Series GST360B industrial desktop adapter. Input construction Class II; 2-pole IEC320-C18, without FG. DC termination Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 36 VDC. Rated current 10 A. Output current range 0–10 A. Rated output power, maximum 360 W. Ripple and noise, maximum 200 mVp-p. Voltage tolerance ±2.0%. Line regulation ±1.0%. Load regulation ±2.0%. Efficiency, typical 94% for this C6P version. Peak power 450 W for 3 seconds. This is a short-duration peak, not a continuous-output rating. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3.8 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 8 ms at both 230 VAC and 115 VAC, at full load. Touch current <0.5 mA at 260 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 135–155% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load from −30 to 35°C, then 80% at 50°C, 65% at 60°C and 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 85% at 100 VAC; the graph holds 85% up to the 120 VAC transition, with 100% from 120 to 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–35°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Operating altitude Up to 5000 m, with altitude and temperature derating. Overvoltage category OVC II under UL62368-1 and BS EN/EN62368-1, up to 5000 m. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug C6P: Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Grounding Class II, without FG; no protective-earth contact in the 2-pole inlet. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Optional DC Terminations MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. These are alternative output terminations available by request, not included mating accessories. MIC4 and C4P are listed for 36–55 V versions. Confirm the required option and its current rating before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, Dekra BS EN/EN62368-1, IEC 61558-1, IEC 61558-2-16, CCC GB4943.1, AS/NZS 61558-1/-2-16 and EAC TP TC 004. Energy-saving compliance USA EISA 2007/DoE and Canada NRCan. Withstand voltage Input/output: 3 kVAC. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Harmonic current / flicker BS EN/EN61000-3-2 Class A; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1400 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.4 kg per unit; 8 pieces / 12 kg / 0.82 CUFT. MTBF, minimum estimates 2057.2 thousand hours, Telcordia SR-332 (Bellcore); 265.9 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 94–97.

  Read more less

  $238.54

  View options

• 

  View options

  MEAN WELL GST360B series: Desktop AC/DC Power Adapter - GST360B24-C6P

  MEAN WELL GST360B24-C6P is a single-output desktop AC/DC power adapter rated at 24 VDC, 15 A and 360 W. It has a C6P DC output plug and a 2-pole IEC320-C18 inlet with Class II insulation. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST360B Datasheet (PDF) The GST360B section is on PDF pages 94, 95, 96, 97. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST360B24-C6P. Series GST360B industrial desktop adapter. Input construction Class II; 2-pole IEC320-C18, without FG. DC termination Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 24 VDC. Rated current 15 A. Output current range 0–15 A. Rated output power, maximum 360 W. Ripple and noise, maximum 200 mVp-p. Voltage tolerance ±3.0%. Line regulation ±1.0%. Load regulation ±3.0%. Efficiency, typical 93% for this C6P version. Peak power 450 W for 3 seconds. This is a short-duration peak, not a continuous-output rating. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3.8 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 8 ms at both 230 VAC and 115 VAC, at full load. Touch current <0.5 mA at 260 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 135–155% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load from −30 to 35°C, then 80% at 50°C, 65% at 60°C and 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 85% at 100 VAC; the graph holds 85% up to the 120 VAC transition, with 100% from 120 to 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–35°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Operating altitude Up to 5000 m, with altitude and temperature derating. Overvoltage category OVC II under UL62368-1 and BS EN/EN62368-1, up to 5000 m. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug C6P: Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Grounding Class II, without FG; no protective-earth contact in the 2-pole inlet. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. DC Connection Selection The default C6P termination is specified for this voltage. The catalogue restricts MIC4 and C4P alternatives to 36–55 V models; select the original C6P arrangement for this 24 V model. Other terminations require a separately confirmed configuration. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, Dekra BS EN/EN62368-1, IEC 61558-1, IEC 61558-2-16, CCC GB4943.1, AS/NZS 61558-1/-2-16 and EAC TP TC 004. Energy-saving compliance USA EISA 2007/DoE and Canada NRCan. Withstand voltage Input/output: 3 kVAC. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Harmonic current / flicker BS EN/EN61000-3-2 Class A; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1400 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.4 kg per unit; 8 pieces / 12 kg / 0.82 CUFT. MTBF, minimum estimates 2057.2 thousand hours, Telcordia SR-332 (Bellcore); 265.9 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 94–97.

  Read more less

  $221.79

  View options

• 

  View options

  MEAN WELL GST360B series: Desktop AC/DC Power Adapter - GST360B15-C8P

  MEAN WELL GST360B15-C8P is a single-output desktop AC/DC power adapter rated at 15 VDC, 22.7 A and 340.5 W. It has a C8P DC output plug and a 2-pole IEC320-C18 inlet with Class II insulation. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST360B Datasheet (PDF) The GST360B section is on PDF pages 94, 95, 96, 97. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST360B15-C8P. Series GST360B industrial desktop adapter. Input construction Class II; 2-pole IEC320-C18, without FG. DC termination Pins 1–4 +Vo; pins 5–8 −Vo. MOLEX 39-01-2080 equivalent. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 15 VDC. Rated current 22.7 A. Output current range 0–22.7 A. Rated output power, maximum 340.5 W. Ripple and noise, maximum 120 mVp-p. Voltage tolerance ±5.0%. Line regulation ±1.0%. Load regulation ±5.0%. Efficiency, typical 92% for this C8P version. Peak power 425 W for 3 seconds. This is a short-duration peak, not a continuous-output rating. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3.8 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 8 ms at both 230 VAC and 115 VAC, at full load. Touch current <0.5 mA at 260 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 135–155% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load from −30 to 35°C, then 80% at 50°C, 65% at 60°C and 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 85% at 100 VAC; the graph holds 85% up to the 120 VAC transition, with 100% from 120 to 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–35°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Operating altitude Up to 5000 m, with altitude and temperature derating. Overvoltage category OVC II under UL62368-1 and BS EN/EN62368-1, up to 5000 m. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 6C; 1000 ±50 mm. Default DC plug C8P: Pins 1–4 +Vo; pins 5–8 −Vo. MOLEX 39-01-2080 equivalent. Grounding Class II, without FG; no protective-earth contact in the 2-pole inlet. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. DC Connection Selection The default C8P termination is specified for this voltage. The catalogue restricts MIC4 and C4P alternatives to 36–55 V models; select the original C8P arrangement for this 15 V model. Other terminations require a separately confirmed configuration. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, Dekra BS EN/EN62368-1, IEC 61558-1, IEC 61558-2-16, CCC GB4943.1, AS/NZS 61558-1/-2-16 and EAC TP TC 004. Energy-saving compliance USA EISA 2007/DoE and Canada NRCan. Withstand voltage Input/output: 3 kVAC. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Harmonic current / flicker BS EN/EN61000-3-2 Class A; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1400 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.4 kg per unit; 8 pieces / 12 kg / 0.82 CUFT. MTBF, minimum estimates 2057.2 thousand hours, Telcordia SR-332 (Bellcore); 265.9 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 94–97.

  Read more less

  $238.54

  View options

• 

  View options

  MEAN WELL GST360B series: Desktop AC/DC Power Adapter - GST360B12-C8P

  MEAN WELL GST360B12-C8P is a single-output desktop AC/DC power adapter rated at 12 VDC, 27.5 A and 330 W. It has a C8P DC output plug and a 2-pole IEC320-C18 inlet with Class II insulation. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST360B Datasheet (PDF) The GST360B section is on PDF pages 94, 95, 96, 97. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST360B12-C8P. Series GST360B industrial desktop adapter. Input construction Class II; 2-pole IEC320-C18, without FG. DC termination Pins 1–4 +Vo; pins 5–8 −Vo. MOLEX 39-01-2080 equivalent. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 12 VDC. Rated current 27.5 A. Output current range 0–27.5 A. Rated output power, maximum 330 W. Ripple and noise, maximum 120 mVp-p. Voltage tolerance ±5.0%. Line regulation ±1.0%. Load regulation ±5.0%. Efficiency, typical 91% for this C8P version. Peak power 415 W for 3 seconds. This is a short-duration peak, not a continuous-output rating. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3.8 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 8 ms at both 230 VAC and 115 VAC, at full load. Touch current <0.5 mA at 260 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 135–155% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load from −30 to 35°C, then 80% at 50°C, 65% at 60°C and 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 85% at 100 VAC; the graph holds 85% up to the 120 VAC transition, with 100% from 120 to 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–35°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Operating altitude Up to 5000 m, with altitude and temperature derating. Overvoltage category OVC II under UL62368-1 and BS EN/EN62368-1, up to 5000 m. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 6C; 1000 ±50 mm. Default DC plug C8P: Pins 1–4 +Vo; pins 5–8 −Vo. MOLEX 39-01-2080 equivalent. Grounding Class II, without FG; no protective-earth contact in the 2-pole inlet. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. DC Connection Selection The default C8P termination is specified for this voltage. The catalogue restricts MIC4 and C4P alternatives to 36–55 V models; select the original C8P arrangement for this 12 V model. Other terminations require a separately confirmed configuration. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, Dekra BS EN/EN62368-1, IEC 61558-1, IEC 61558-2-16, CCC GB4943.1, AS/NZS 61558-1/-2-16 and EAC TP TC 004. Energy-saving compliance USA EISA 2007/DoE and Canada NRCan. Withstand voltage Input/output: 3 kVAC. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Harmonic current / flicker BS EN/EN61000-3-2 Class A; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1400 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.4 kg per unit; 8 pieces / 12 kg / 0.82 CUFT. MTBF, minimum estimates 2057.2 thousand hours, Telcordia SR-332 (Bellcore); 265.9 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 94–97.

  Read more less

  $238.54

  View options

• 

  View options

  MEAN WELL GST360A series: Desktop AC/DC Power Adapter - GST360A55-C6P

  MEAN WELL GST360A55-C6P is a single-output desktop AC/DC power adapter rated at 55 VDC, 6.55 A and 360 W. It has a C6P DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST360A Datasheet (PDF) The GST360A section is on PDF pages 90, 91, 92, 93. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST360A55-C6P. Series GST360A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 55 VDC. Rated current 6.55 A. Output current range 0–6.55 A. Rated output power, maximum 360 W. Ripple and noise, maximum 200 mVp-p. Voltage tolerance ±2.0%. Line regulation ±1.0%. Load regulation ±2.0%. Efficiency, typical 95% for this C6P version. Peak power 450 W for 3 seconds. This is a short-duration peak, not a continuous-output rating. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3.8 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 8 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 1.5 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 135–155% of rated output power. Output shutdown; reapply input power to recover. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load from −30 to 40°C, then 80% at 50°C, 65% at 60°C and 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 85% at 100 VAC; the graph holds 85% up to the 120 VAC transition, with 100% from 120 to 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–40°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Operating altitude Up to 5000 m, with altitude and temperature derating. Overvoltage category OVC II under UL62368-1 and BS EN/EN62368-1, up to 5000 m. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug C6P: Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. A DC −V-to-FG isolated option is available by request; it is not the standard configuration. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Optional DC Terminations MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. These are alternative output terminations available by request, not included mating accessories. MIC4 and C4P are listed for 36–55 V versions. Confirm the required option and its current rating before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, Dekra BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943, AS/NZS 62368.1, PSE J62368-1, BIS IS13252, KC 62368-1 and EAC TP TC 004. Energy-saving compliance USA EISA 2007/DoE and Canada NRCan. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1400 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.4 kg per unit; 8 pieces / 12 kg / 0.82 CUFT. MTBF, minimum estimates 2068.5 thousand hours, Telcordia SR-332 (Bellcore); 269 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 90–93.

  Read more less

  $238.54

  View options

• 

  View options

  MEAN WELL GST360A series: Desktop AC/DC Power Adapter - GST360A48-C6P

  MEAN WELL GST360A48-C6P is a single-output desktop AC/DC power adapter rated at 48 VDC, 7.5 A and 360 W. It has a C6P DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST360A Datasheet (PDF) The GST360A section is on PDF pages 90, 91, 92, 93. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST360A48-C6P. Series GST360A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 48 VDC. Rated current 7.5 A. Output current range 0–7.5 A. Rated output power, maximum 360 W. Ripple and noise, maximum 200 mVp-p. Voltage tolerance ±2.0%. Line regulation ±1.0%. Load regulation ±2.0%. Efficiency, typical 95% for this C6P version. Peak power 450 W for 3 seconds. This is a short-duration peak, not a continuous-output rating. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3.8 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 8 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 1.5 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 135–155% of rated output power. Output shutdown; reapply input power to recover. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load from −30 to 40°C, then 80% at 50°C, 65% at 60°C and 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 85% at 100 VAC; the graph holds 85% up to the 120 VAC transition, with 100% from 120 to 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–40°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Operating altitude Up to 5000 m, with altitude and temperature derating. Overvoltage category OVC II under UL62368-1 and BS EN/EN62368-1, up to 5000 m. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug C6P: Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. A DC −V-to-FG isolated option is available by request; it is not the standard configuration. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Optional DC Terminations MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. These are alternative output terminations available by request, not included mating accessories. MIC4 and C4P are listed for 36–55 V versions. Confirm the required option and its current rating before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, Dekra BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943, AS/NZS 62368.1, PSE J62368-1, BIS IS13252, KC 62368-1 and EAC TP TC 004. Energy-saving compliance USA EISA 2007/DoE and Canada NRCan. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1400 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.4 kg per unit; 8 pieces / 12 kg / 0.82 CUFT. MTBF, minimum estimates 2068.5 thousand hours, Telcordia SR-332 (Bellcore); 269 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 90–93.

  Read more less

  $238.54

  View options

• 

  View options

  MEAN WELL GST360A series: Desktop AC/DC Power Adapter - GST360A36-C6P

  MEAN WELL GST360A36-C6P is a single-output desktop AC/DC power adapter rated at 36 VDC, 10 A and 360 W. It has a C6P DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST360A Datasheet (PDF) The GST360A section is on PDF pages 90, 91, 92, 93. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST360A36-C6P. Series GST360A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 36 VDC. Rated current 10 A. Output current range 0–10 A. Rated output power, maximum 360 W. Ripple and noise, maximum 200 mVp-p. Voltage tolerance ±2.0%. Line regulation ±1.0%. Load regulation ±2.0%. Efficiency, typical 94% for this C6P version. Peak power 450 W for 3 seconds. This is a short-duration peak, not a continuous-output rating. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3.8 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 8 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 1.5 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 135–155% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load from −30 to 40°C, then 80% at 50°C, 65% at 60°C and 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 85% at 100 VAC; the graph holds 85% up to the 120 VAC transition, with 100% from 120 to 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–40°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Operating altitude Up to 5000 m, with altitude and temperature derating. Overvoltage category OVC II under UL62368-1 and BS EN/EN62368-1, up to 5000 m. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug C6P: Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. A DC −V-to-FG isolated option is available by request; it is not the standard configuration. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Optional DC Terminations MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. These are alternative output terminations available by request, not included mating accessories. MIC4 and C4P are listed for 36–55 V versions. Confirm the required option and its current rating before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, Dekra BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943, AS/NZS 62368.1, PSE J62368-1, BIS IS13252, KC 62368-1 and EAC TP TC 004. Energy-saving compliance USA EISA 2007/DoE and Canada NRCan. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1400 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.4 kg per unit; 8 pieces / 12 kg / 0.82 CUFT. MTBF, minimum estimates 2068.5 thousand hours, Telcordia SR-332 (Bellcore); 269 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 90–93.

  Read more less

  $238.54

  View options

• 

  View options

  MEAN WELL GST360A series: Desktop AC/DC Power Adapter - GST360A24-C6P

  MEAN WELL GST360A24-C6P is a single-output desktop AC/DC power adapter rated at 24 VDC, 15 A and 360 W. It has a C6P DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST360A Datasheet (PDF) The GST360A section is on PDF pages 90, 91, 92, 93. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST360A24-C6P. Series GST360A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 24 VDC. Rated current 15 A. Output current range 0–15 A. Rated output power, maximum 360 W. Ripple and noise, maximum 200 mVp-p. Voltage tolerance ±3.0%. Line regulation ±1.0%. Load regulation ±3.0%. Efficiency, typical 93% for this C6P version. Peak power 450 W for 3 seconds. This is a short-duration peak, not a continuous-output rating. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3.8 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 8 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 1.5 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 135–155% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load from −30 to 40°C, then 80% at 50°C, 65% at 60°C and 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 85% at 100 VAC; the graph holds 85% up to the 120 VAC transition, with 100% from 120 to 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–40°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Operating altitude Up to 5000 m, with altitude and temperature derating. Overvoltage category OVC II under UL62368-1 and BS EN/EN62368-1, up to 5000 m. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug C6P: Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. A DC −V-to-FG isolated option is available by request; it is not the standard configuration. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. DC Connection Selection The default C6P termination is specified for this voltage. The catalogue restricts MIC4 and C4P alternatives to 36–55 V models; select the original C6P arrangement for this 24 V model. Other terminations require a separately confirmed configuration. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, Dekra BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943, AS/NZS 62368.1, PSE J62368-1, BIS IS13252, KC 62368-1 and EAC TP TC 004. Energy-saving compliance USA EISA 2007/DoE and Canada NRCan. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1400 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.4 kg per unit; 8 pieces / 12 kg / 0.82 CUFT. MTBF, minimum estimates 2068.5 thousand hours, Telcordia SR-332 (Bellcore); 269 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 90–93.

  Read more less

  $221.79

  View options

• 

  View options

  MEAN WELL GST360A series: Desktop AC/DC Power Adapter - GST360A15-C8P

  MEAN WELL GST360A15-C8P is a single-output desktop AC/DC power adapter rated at 15 VDC, 22.7 A and 340.5 W. It has a C8P DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST360A Datasheet (PDF) The GST360A section is on PDF pages 90, 91, 92, 93. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST360A15-C8P. Series GST360A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1–4 +Vo; pins 5–8 −Vo. MOLEX 39-01-2080 equivalent. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 15 VDC. Rated current 22.7 A. Output current range 0–22.7 A. Rated output power, maximum 340.5 W. Ripple and noise, maximum 120 mVp-p. Voltage tolerance ±5.0%. Line regulation ±1.0%. Load regulation ±5.0%. Efficiency, typical 92% for this C8P version. Peak power 425 W for 3 seconds. This is a short-duration peak, not a continuous-output rating. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3.8 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 8 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 1.5 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 135–155% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load from −30 to 40°C, then 80% at 50°C, 65% at 60°C and 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 85% at 100 VAC; the graph holds 85% up to the 120 VAC transition, with 100% from 120 to 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–40°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Operating altitude Up to 5000 m, with altitude and temperature derating. Overvoltage category OVC II under UL62368-1 and BS EN/EN62368-1, up to 5000 m. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 6C; 1000 ±50 mm. Default DC plug C8P: Pins 1–4 +Vo; pins 5–8 −Vo. MOLEX 39-01-2080 equivalent. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. A DC −V-to-FG isolated option is available by request; it is not the standard configuration. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. DC Connection Selection The default C8P termination is specified for this voltage. The catalogue restricts MIC4 and C4P alternatives to 36–55 V models; select the original C8P arrangement for this 15 V model. Other terminations require a separately confirmed configuration. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, Dekra BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943, AS/NZS 62368.1, PSE J62368-1, BIS IS13252, KC 62368-1 and EAC TP TC 004. Energy-saving compliance USA EISA 2007/DoE and Canada NRCan. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1400 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.4 kg per unit; 8 pieces / 12 kg / 0.82 CUFT. MTBF, minimum estimates 2068.5 thousand hours, Telcordia SR-332 (Bellcore); 269 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 90–93.

  Read more less

  $238.54

  View options

• 

  View options

  MEAN WELL GST360A series: Desktop AC/DC Power Adapter - GST360A12-C8P

  MEAN WELL GST360A12-C8P is a single-output desktop AC/DC power adapter rated at 12 VDC, 27.5 A and 330 W. It has a C8P DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST360A Datasheet (PDF) The GST360A section is on PDF pages 90, 91, 92, 93. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST360A12-C8P. Series GST360A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1–4 +Vo; pins 5–8 −Vo. MOLEX 39-01-2080 equivalent. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 12 VDC. Rated current 27.5 A. Output current range 0–27.5 A. Rated output power, maximum 330 W. Ripple and noise, maximum 120 mVp-p. Voltage tolerance ±5.0%. Line regulation ±1.0%. Load regulation ±5.0%. Efficiency, typical 91% for this C8P version. Peak power 415 W for 3 seconds. This is a short-duration peak, not a continuous-output rating. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3.8 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 8 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 1.5 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 135–155% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load from −30 to 40°C, then 80% at 50°C, 65% at 60°C and 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 85% at 100 VAC; the graph holds 85% up to the 120 VAC transition, with 100% from 120 to 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–40°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Operating altitude Up to 5000 m, with altitude and temperature derating. Overvoltage category OVC II under UL62368-1 and BS EN/EN62368-1, up to 5000 m. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 6C; 1000 ±50 mm. Default DC plug C8P: Pins 1–4 +Vo; pins 5–8 −Vo. MOLEX 39-01-2080 equivalent. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. A DC −V-to-FG isolated option is available by request; it is not the standard configuration. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. DC Connection Selection The default C8P termination is specified for this voltage. The catalogue restricts MIC4 and C4P alternatives to 36–55 V models; select the original C8P arrangement for this 12 V model. Other terminations require a separately confirmed configuration. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, Dekra BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943, AS/NZS 62368.1, PSE J62368-1, BIS IS13252, KC 62368-1 and EAC TP TC 004. Energy-saving compliance USA EISA 2007/DoE and Canada NRCan. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1400 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.4 kg per unit; 8 pieces / 12 kg / 0.82 CUFT. MTBF, minimum estimates 2068.5 thousand hours, Telcordia SR-332 (Bellcore); 269 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 90–93.

  Read more less

  $238.54

  View options

• 

  View options

  MEAN WELL GST280A series: Desktop AC/DC Power Adapter - GST280A48-C6P

  MEAN WELL GST280A48-C6P is a single-output desktop AC/DC power adapter rated at 48 VDC, 5.84 A and 280.32 W. It has a C6P DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST280A Datasheet (PDF) The GST280A section is on PDF pages 86, 87, 88, 89. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST280A48-C6P. Series GST280A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 48 VDC. Rated current 5.84 A. Output current range 0–5.84 A. Rated output power, maximum 280.32 W. Ripple and noise, maximum 200 mVp-p. Voltage tolerance ±2.0%. Line regulation ±1.0%. Load regulation ±2.0%. Efficiency, typical 94% for this C6P version. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3 A at 115 VAC; 1.5 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 20 ms at 230 VAC; 2000 ms / 20 ms at 115 VAC, at full load. Hold-up time, typical 16 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 1.5 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 105–135% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load through 40°C, decreasing to 50% at 70°C. Input-voltage derating At 60 Hz, 60% load at 85 VAC, rising to 100% at 100 VAC and remaining at 100% through 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–40°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug C6P: Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Optional DC Terminations R7BF Pins 1 and 4 +Vo; pins 2 and 3 −Vo. Female locking 4-pin DIN, KYCON KPJX-CM-4S equivalent. MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. These are alternative output terminations available by request, not included mating accessories. Confirm the required option and its current rating before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, TUV BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943.1, PSE J62368-1, AS/NZS 62368.1, BIS IS13252, KC K60950-1 and EAC TP TC 004. Energy-saving compliance EISA 2007/DoE, NRCan, Korea K-MEPS, AU/NZ MEPS and EU ErP. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1250 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.25 kg per unit; 12 pieces / 16 kg / 1.09 CUFT. MTBF, minimum estimates 1625.8 thousand hours, Telcordia SR-332 (Bellcore); 181.2 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 86–89.

  Read more less

  $198.62

  View options

• 

  View options

  MEAN WELL GST280A series: Desktop AC/DC Power Adapter - GST280A24-C6P

  MEAN WELL GST280A24-C6P is a single-output desktop AC/DC power adapter rated at 24 VDC, 11.67 A and 280.08 W. It has a C6P DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST280A Datasheet (PDF) The GST280A section is on PDF pages 86, 87, 88, 89. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST280A24-C6P. Series GST280A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 24 VDC. Rated current 11.67 A. Output current range 0–11.67 A. Rated output power, maximum 280.08 W. Ripple and noise, maximum 200 mVp-p. Voltage tolerance ±3.0%. Line regulation ±1.0%. Load regulation ±3.0%. Efficiency, typical 93% for this C6P version. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3 A at 115 VAC; 1.5 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 20 ms at 230 VAC; 2000 ms / 20 ms at 115 VAC, at full load. Hold-up time, typical 16 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 1.5 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 105–135% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load through 40°C, decreasing to 50% at 70°C. Input-voltage derating At 60 Hz, 60% load at 85 VAC, rising to 100% at 100 VAC and remaining at 100% through 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–40°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug C6P: Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Optional DC Terminations R7BF Pins 1 and 4 +Vo; pins 2 and 3 −Vo. Female locking 4-pin DIN, KYCON KPJX-CM-4S equivalent. MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. These are alternative output terminations available by request, not included mating accessories. Confirm the required option and its current rating before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, TUV BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943.1, PSE J62368-1, AS/NZS 62368.1, BIS IS13252, KC K60950-1 and EAC TP TC 004. Energy-saving compliance EISA 2007/DoE, NRCan, Korea K-MEPS, AU/NZ MEPS and EU ErP. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1250 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.25 kg per unit; 12 pieces / 16 kg / 1.09 CUFT. MTBF, minimum estimates 1625.8 thousand hours, Telcordia SR-332 (Bellcore); 181.2 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 86–89.

  Read more less

  $184.82

  View options

• 

  View options

  MEAN WELL GST280A series: Desktop AC/DC Power Adapter - GST280A20-C6P

  MEAN WELL GST280A20-C6P is a single-output desktop AC/DC power adapter rated at 20 VDC, 13 A and 260 W. It has a C6P DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST280A Datasheet (PDF) The GST280A section is on PDF pages 86, 87, 88, 89. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST280A20-C6P. Series GST280A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 20 VDC. Rated current 13 A. Output current range 0–13 A. Rated output power, maximum 260 W. Ripple and noise, maximum 150 mVp-p. Voltage tolerance ±4.0%. Line regulation ±1.0%. Load regulation ±4.0%. Efficiency, typical 92% for this C6P version. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3 A at 115 VAC; 1.5 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 20 ms at 230 VAC; 2000 ms / 20 ms at 115 VAC, at full load. Hold-up time, typical 16 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 1.5 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 105–135% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: full load through 40°C, decreasing to 50% at 70°C. Input-voltage derating At 60 Hz, 60% load at 85 VAC, rising to 100% at 100 VAC and remaining at 100% through 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–40°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug C6P: Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Optional DC Terminations R7BF Pins 1 and 4 +Vo; pins 2 and 3 −Vo. Female locking 4-pin DIN, KYCON KPJX-CM-4S equivalent. MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. These are alternative output terminations available by request, not included mating accessories. Confirm the required option and its current rating before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, TUV BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943.1, PSE J62368-1, AS/NZS 62368.1, BIS IS13252, KC K60950-1 and EAC TP TC 004. Energy-saving compliance EISA 2007/DoE, NRCan, Korea K-MEPS, AU/NZ MEPS and EU ErP. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1250 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.25 kg per unit; 12 pieces / 16 kg / 1.09 CUFT. MTBF, minimum estimates 1625.8 thousand hours, Telcordia SR-332 (Bellcore); 181.2 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 86–89.

  Read more less

  $198.62

  View options

• 

  View options

  MEAN WELL GST280A series: Desktop AC/DC Power Adapter - GST280A15-C6P

  MEAN WELL GST280A15-C6P is a single-output desktop AC/DC power adapter rated at 15 VDC, 17 A and 255 W. It has a C6P DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST280A Datasheet (PDF) The GST280A section is on PDF pages 86, 87, 88, 89. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST280A15-C6P. Series GST280A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 15 VDC. Rated current 17 A. Output current range 0–17 A. Rated output power, maximum 255 W. Ripple and noise, maximum 120 mVp-p. Voltage tolerance ±5.0%. Line regulation ±1.0%. Load regulation ±5.0%. Efficiency, typical 90% for this C6P version. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3 A at 115 VAC; 1.5 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 20 ms at 230 VAC; 2000 ms / 20 ms at 115 VAC, at full load. Hold-up time, typical 16 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 1.5 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 105–135% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: the 110 VAC curve for this 15 V model allows full load through 35°C, while the other-input curve allows full load through 40°C; both decrease to 50% at 70°C. Input-voltage derating At 60 Hz, 60% load at 85 VAC, rising to 100% at 110 VAC and remaining at 100% through 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–40°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug C6P: Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Optional DC Terminations R7BF Pins 1 and 4 +Vo; pins 2 and 3 −Vo. Female locking 4-pin DIN, KYCON KPJX-CM-4S equivalent. MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. These are alternative output terminations available by request, not included mating accessories. Confirm the required option and its current rating before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, TUV BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943.1, PSE J62368-1, AS/NZS 62368.1, BIS IS13252, KC K60950-1 and EAC TP TC 004. Energy-saving compliance EISA 2007/DoE, NRCan, Korea K-MEPS, AU/NZ MEPS and EU ErP. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1250 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.25 kg per unit; 12 pieces / 16 kg / 1.09 CUFT. MTBF, minimum estimates 1625.8 thousand hours, Telcordia SR-332 (Bellcore); 181.2 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 86–89.

  Read more less

  $198.62

  View options

• 

  View options

  MEAN WELL GST280A series: Desktop AC/DC Power Adapter - GST280A12-C6P

  MEAN WELL GST280A12-C6P is a single-output desktop AC/DC power adapter rated at 12 VDC, 21 A and 252 W. It has a C6P DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST280A Datasheet (PDF) The GST280A section is on PDF pages 86, 87, 88, 89. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST280A12-C6P. Series GST280A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.5 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 12 VDC. Rated current 21 A. Output current range 0–21 A. Rated output power, maximum 252 W. Ripple and noise, maximum 120 mVp-p. Voltage tolerance ±5.0%. Line regulation ±1.0%. Load regulation ±5.0%. Efficiency, typical 89.5% for this C6P version. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.95 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 3 A at 115 VAC; 1.5 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 20 ms at 230 VAC; 2000 ms / 20 ms at 115 VAC, at full load. Hold-up time, typical 16 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 1.5 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 105–135% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Output shutdown; reapply input power to recover. Overtemperature Output shutdown; reapply input power to recover. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: the 110 VAC curve for this 12 V model allows full load through 35°C, while the other-input curve allows full load through 40°C; both decrease to 50% at 70°C. Input-voltage derating At 60 Hz, 60% load at 85 VAC, rising to 100% at 110 VAC and remaining at 100% through 264 VAC. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–40°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 220 × 95 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug C6P: Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Optional DC Terminations R7BF Pins 1 and 4 +Vo; pins 2 and 3 −Vo. Female locking 4-pin DIN, KYCON KPJX-CM-4S equivalent. MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. These are alternative output terminations available by request, not included mating accessories. Confirm the required option and its current rating before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, TUV BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943.1, PSE J62368-1, AS/NZS 62368.1, BIS IS13252, KC K60950-1 and EAC TP TC 004. Energy-saving compliance EISA 2007/DoE, NRCan, Korea K-MEPS, AU/NZ MEPS and EU ErP. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1250 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.25 kg per unit; 12 pieces / 16 kg / 1.09 CUFT. MTBF, minimum estimates 1625.8 thousand hours, Telcordia SR-332 (Bellcore); 181.2 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 86–89.

  Read more less

  $198.62

  View options

• 

  View options

  MEAN WELL GST220A series: Desktop AC/DC Power Adapter - GST220A48-R7B

  MEAN WELL GST220A48-R7B is a single-output desktop AC/DC power adapter rated at 48 VDC, 4.6 A and 221 W. It has a R7B DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST220A Datasheet (PDF) The GST220A section is on PDF pages 81, 82, 83, 84, 85. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST220A48-R7B. Series GST220A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1 and 4 +Vo; pins 2 and 3 −Vo. KYCON KPPX-4P equivalent. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.15 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 48 VDC. Rated current 4.6 A. Output current range 0–4.6 A. Rated output power, maximum 221 W. Ripple and noise, maximum 200 mVp-p. Voltage tolerance ±2.0%. Line regulation ±1.0%. Load regulation ±2.0%. Efficiency, typical 94.5% for this R7B version. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.91 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 4 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 20 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 0.75 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 105–135% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Hiccup mode, specified at 10% load. Overtemperature Output shutdown; automatic recovery after the temperature decreases. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: at 230 VAC, full load through 50°C. At 100 VAC, full load through 40°C. Both curves decrease to 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 100% at 95 VAC. Full load is then available through 264 VAC, subject to temperature derating. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–50°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 210 × 85 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug R7B: Pins 1 and 4 +Vo; pins 2 and 3 −Vo. KYCON KPPX-4P equivalent. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Alternative DC Plugs and Accessories P1J Straight tuning-fork type; 5.5 mm OD × 2.1 mm ID × 11.0 mm length. P1M Straight tuning-fork type; 5.5 mm OD × 2.5 mm ID × 11.0 mm length. R7BF Pins 1 and 4 +Vo; pins 2 and 3 −Vo. Female locking 4-pin DIN, KYCON KPJX-CM-4S equivalent. R1B Pins 1, 2 and 4 −Vo; pins 3 and 5 +Vo. Male 5-pin DIN. MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C6P Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. The optional output connector is not connected to FG. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. The optional output connector is not connected to FG. Stripped and tinned leads Available by customer request: lead 1 +Vo, lead 2 −Vo; standard exposed lengths L = 25 mm and L1 = 5 mm. Wire colors are illustrative; follow the delivered product. Alternative terminations can be specified as a customized cable subject to minimum order quantity. Only the options explicitly marked as quick adapters are available as separate accessories without minimum order quantity; the plug kit is sold separately. P1J and P1M quick adapters are listed for 48 V output only, with a 7.5 A maximum accessory current rating. Confirm the complete accessory configuration, polarity and allowable current before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, TUV BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943.1, PSE J62368-1, AS/NZS 62368.1, BIS IS13252, KC K60950-1 and EAC TP TC 004. Energy-saving compliance EISA 2007/DoE, NRCan, Korea K-MEPS, AU/NZ MEPS and EU ErP and CoC Version 5. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. Generic immunity standard BS EN/EN55035. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1100 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.1 kg per unit; 12 pieces / 14.2 kg / 0.81 CUFT. MTBF, minimum estimates 2006.1 thousand hours, Telcordia SR-332 (Bellcore); 209.4 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 81–85.

  Read more less

  $160.18

  View options

• 

  View options

  MEAN WELL GST220A series: Desktop AC/DC Power Adapter - GST220A36-R7B

  MEAN WELL GST220A36-R7B is a single-output desktop AC/DC power adapter rated at 36 VDC, 6.1 A and 219.6 W. It has a R7B DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST220A Datasheet (PDF) The GST220A section is on PDF pages 81, 82, 83, 84, 85. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST220A36-R7B. Series GST220A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1 and 4 +Vo; pins 2 and 3 −Vo. KYCON KPPX-4P equivalent. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.15 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 36 VDC. Rated current 6.1 A. Output current range 0–6.1 A. Rated output power, maximum 219.6 W. Ripple and noise, maximum 200 mVp-p. Voltage tolerance ±2.0%. Line regulation ±1.0%. Load regulation ±2.0%. Efficiency, typical 93% for this R7B version. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.91 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 4 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 20 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 0.75 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 105–135% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Hiccup mode, specified at 10% load. Overtemperature Output shutdown; automatic recovery after the temperature decreases. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: at 230 VAC, full load through 50°C. At 100 VAC, full load through 40°C. Both curves decrease to 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 100% at 95 VAC. Full load is then available through 264 VAC, subject to temperature derating. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–50°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 210 × 85 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug R7B: Pins 1 and 4 +Vo; pins 2 and 3 −Vo. KYCON KPPX-4P equivalent. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Alternative DC Plugs and Accessories P1J Straight tuning-fork type; 5.5 mm OD × 2.1 mm ID × 11.0 mm length. P1M Straight tuning-fork type; 5.5 mm OD × 2.5 mm ID × 11.0 mm length. R7BF Pins 1 and 4 +Vo; pins 2 and 3 −Vo. Female locking 4-pin DIN, KYCON KPJX-CM-4S equivalent. R1B Pins 1, 2 and 4 −Vo; pins 3 and 5 +Vo. Male 5-pin DIN. MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C6P Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. The optional output connector is not connected to FG. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. The optional output connector is not connected to FG. Stripped and tinned leads Available by customer request: lead 1 +Vo, lead 2 −Vo; standard exposed lengths L = 25 mm and L1 = 5 mm. Wire colors are illustrative; follow the delivered product. Alternative terminations can be specified as a customized cable subject to minimum order quantity. Only the options explicitly marked as quick adapters are available as separate accessories without minimum order quantity; the plug kit is sold separately. P1J and P1M quick adapters are listed for 48 V output only, with a 7.5 A maximum accessory current rating. Confirm the complete accessory configuration, polarity and allowable current before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, TUV EN62368-1, BSMI CNS15598-1, CCC GB4943.1, PSE J62368-1 and AS/NZS 62368.1. The 36 V approval list does not include BIS, KC or EAC. Energy-saving compliance EISA 2007/DoE, NRCan, Korea K-MEPS, AU/NZ MEPS and EU ErP and CoC Version 5. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. Generic immunity standard BS EN/EN55035. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1100 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.1 kg per unit; 12 pieces / 14.2 kg / 0.81 CUFT. MTBF, minimum estimates 2006.1 thousand hours, Telcordia SR-332 (Bellcore); 209.4 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 81–85.

  Read more less

  $160.18

  View options

• 

  View options

  MEAN WELL GST220A series: Desktop AC/DC Power Adapter - GST220A24-R7B

  MEAN WELL GST220A24-R7B is a single-output desktop AC/DC power adapter rated at 24 VDC, 9.2 A and 221 W. It has a R7B DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST220A Datasheet (PDF) The GST220A section is on PDF pages 81, 82, 83, 84, 85. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST220A24-R7B. Series GST220A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1 and 4 +Vo; pins 2 and 3 −Vo. KYCON KPPX-4P equivalent. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.15 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 24 VDC. Rated current 9.2 A. Output current range 0–9.2 A. Rated output power, maximum 221 W. Ripple and noise, maximum 150 mVp-p. Voltage tolerance ±3.0%. Line regulation ±1.0%. Load regulation ±3.0%. Efficiency, typical 93.5% for this R7B version. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.91 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 4 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 20 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 0.75 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 105–135% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Hiccup mode, specified at 10% load. Overtemperature Output shutdown; automatic recovery after the temperature decreases. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: at 230 VAC, full load through 50°C. At 100 VAC, full load through 40°C. Both curves decrease to 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 100% at 95 VAC. Full load is then available through 264 VAC, subject to temperature derating. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–50°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 210 × 85 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug R7B: Pins 1 and 4 +Vo; pins 2 and 3 −Vo. KYCON KPPX-4P equivalent. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Alternative DC Plugs and Accessories P1J Straight tuning-fork type; 5.5 mm OD × 2.1 mm ID × 11.0 mm length. P1M Straight tuning-fork type; 5.5 mm OD × 2.5 mm ID × 11.0 mm length. R7BF Pins 1 and 4 +Vo; pins 2 and 3 −Vo. Female locking 4-pin DIN, KYCON KPJX-CM-4S equivalent. R1B Pins 1, 2 and 4 −Vo; pins 3 and 5 +Vo. Male 5-pin DIN. MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C6P Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. The optional output connector is not connected to FG. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. The optional output connector is not connected to FG. Stripped and tinned leads Available by customer request: lead 1 +Vo, lead 2 −Vo; standard exposed lengths L = 25 mm and L1 = 5 mm. Wire colors are illustrative; follow the delivered product. Alternative terminations can be specified as a customized cable subject to minimum order quantity. Only the options explicitly marked as quick adapters are available as separate accessories without minimum order quantity; the plug kit is sold separately. P1J and P1M quick adapters are listed for 48 V output only, with a 7.5 A maximum accessory current rating. Confirm the complete accessory configuration, polarity and allowable current before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, TUV BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943.1, PSE J62368-1, AS/NZS 62368.1, BIS IS13252, KC K60950-1 and EAC TP TC 004. Energy-saving compliance EISA 2007/DoE, NRCan, Korea K-MEPS, AU/NZ MEPS and EU ErP and CoC Version 5. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. Generic immunity standard BS EN/EN55035. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1100 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.1 kg per unit; 12 pieces / 14.2 kg / 0.81 CUFT. MTBF, minimum estimates 2006.1 thousand hours, Telcordia SR-332 (Bellcore); 209.4 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 81–85.

  Read more less

  $148.84

  View options

• 

  View options

  MEAN WELL GST220A series: Desktop AC/DC Power Adapter - GST220A20-R7B

  MEAN WELL GST220A20-R7B is a single-output desktop AC/DC power adapter rated at 20 VDC, 11 A and 220 W. It has a R7B DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST220A Datasheet (PDF) The GST220A section is on PDF pages 81, 82, 83, 84, 85. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST220A20-R7B. Series GST220A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1 and 4 +Vo; pins 2 and 3 −Vo. KYCON KPPX-4P equivalent. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.15 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 20 VDC. Rated current 11 A. Output current range 0–11 A. Rated output power, maximum 220 W. Ripple and noise, maximum 120 mVp-p. Voltage tolerance ±4.0%. Line regulation ±1.0%. Load regulation ±4.0%. Efficiency, typical 92% for this R7B version. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.91 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 4 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 20 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 0.75 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 105–135% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Hiccup mode, specified at 10% load. Overtemperature Output shutdown; automatic recovery after the temperature decreases. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: at 230 VAC, full load through 50°C. At 100 VAC, full load through 40°C. Both curves decrease to 50% at 70°C. Input-voltage derating At 60 Hz, 70% load at 85 VAC, rising to 100% at 95 VAC. Full load is then available through 264 VAC, subject to temperature derating. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–50°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 210 × 85 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug R7B: Pins 1 and 4 +Vo; pins 2 and 3 −Vo. KYCON KPPX-4P equivalent. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Alternative DC Plugs and Accessories P1J Straight tuning-fork type; 5.5 mm OD × 2.1 mm ID × 11.0 mm length. P1M Straight tuning-fork type; 5.5 mm OD × 2.5 mm ID × 11.0 mm length. R7BF Pins 1 and 4 +Vo; pins 2 and 3 −Vo. Female locking 4-pin DIN, KYCON KPJX-CM-4S equivalent. R1B Pins 1, 2 and 4 −Vo; pins 3 and 5 +Vo. Male 5-pin DIN. MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C6P Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. The optional output connector is not connected to FG. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. The optional output connector is not connected to FG. Stripped and tinned leads Available by customer request: lead 1 +Vo, lead 2 −Vo; standard exposed lengths L = 25 mm and L1 = 5 mm. Wire colors are illustrative; follow the delivered product. Alternative terminations can be specified as a customized cable subject to minimum order quantity. Only the options explicitly marked as quick adapters are available as separate accessories without minimum order quantity; the plug kit is sold separately. P1J and P1M quick adapters are listed for 48 V output only, with a 7.5 A maximum accessory current rating. Confirm the complete accessory configuration, polarity and allowable current before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, TUV BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943.1, PSE J62368-1, AS/NZS 62368.1, BIS IS13252, KC K60950-1 and EAC TP TC 004. Energy-saving compliance EISA 2007/DoE, NRCan, Korea K-MEPS, AU/NZ MEPS and EU ErP and CoC Version 5. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. Generic immunity standard BS EN/EN55035. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1100 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.1 kg per unit; 12 pieces / 14.2 kg / 0.81 CUFT. MTBF, minimum estimates 2006.1 thousand hours, Telcordia SR-332 (Bellcore); 209.4 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 81–85.

  Read more less

  $160.18

  View options

• 

  View options

  MEAN WELL GST220A series: Desktop AC/DC Power Adapter - GST220A15-R7B

  MEAN WELL GST220A15-R7B is a single-output desktop AC/DC power adapter rated at 15 VDC, 13.4 A and 201 W. It has a R7B DC output plug and a 3-pole IEC320-C14 inlet with Class I protective earthing. Apply the input-voltage and temperature derating limits below. Product Datasheet Download MEAN WELL GST220A Datasheet (PDF) The GST220A section is on PDF pages 81, 82, 83, 84, 85. Refer to the complete mechanical drawings and notes when planning installation. Model and Selection Complete model GST220A15-R7B. Series GST220A industrial desktop adapter. Input construction Class I; 3-pole IEC320-C14, with FG. DC termination Pins 1 and 4 +Vo; pins 2 and 3 −Vo. KYCON KPPX-4P equivalent. Power conversion Universal input with built-in active PFC. Enclosure and indication Fully enclosed 94V-0 flame-retardant plastic case; LED power-on indicator. No-load consumption <0.15 W. Energy efficiency Level VI. Select the complete model, output voltage, current capacity, connector and polarity for the load. A matching connector shape alone does not establish electrical compatibility. Output Ratings Nominal output 15 VDC. Rated current 13.4 A. Output current range 0–13.4 A. Rated output power, maximum 201 W. Ripple and noise, maximum 100 mVp-p. Voltage tolerance ±5.0%. Line regulation ±1.0%. Load regulation ±5.0%. Efficiency, typical 90% for this R7B version. Observe the stated current and power limits together. Unless otherwise specified, measurements use 230 VAC, rated load, 25°C and 70% RH. Voltage tolerance includes set-up tolerance, line regulation and load regulation. Line regulation is measured from low to high input at rated load. Ripple and noise are measured at 20 MHz bandwidth using a 12-inch twisted pair terminated with parallel 0.1 µF and 47 µF capacitors. The output-voltage set point is measured at the DC plug terminals with 50% load. Input and Timing AC input 85–264 VAC; 47–63 Hz. DC input 120–370 VDC. Power factor, typical PF >0.91 at 230 VAC and PF >0.98 at 115 VAC, at full load. AC current, typical 4 A at 115 VAC; 2 A at 230 VAC. Cold-start inrush, maximum 95 A at 115 VAC; 120 A at 230 VAC. Set-up / rise time 2000 ms / 50 ms at 230 VAC; 2000 ms / 50 ms at 115 VAC, at full load. Hold-up time, typical 20 ms at both 230 VAC and 115 VAC, at full load. Leakage current, maximum 0.75 mA at 240 VAC. Set-up time is measured at the first cold start. Repeated power switching may increase the set-up time. Apply the low-input derating curve. Protection Short circuit / overload 105–135% of rated output power. Hiccup mode; automatic recovery after fault removal. Overvoltage 105–135% of rated output voltage. Hiccup mode, specified at 10% load. Overtemperature Output shutdown; automatic recovery after the temperature decreases. Cooling and Environment Working ambient −30 to +70°C, subject to the model-specific derating curves. Temperature derating Horizontal installation: at 230 VAC, full load through 50°C. At 110 VAC, full load through 40°C. Both curves decrease to 50% at 70°C. Input-voltage derating At 60 Hz, 60% load at 85 VAC, rising to 100% at 100 VAC. Full load is then available through 264 VAC, subject to temperature derating. Working humidity 20–90% RH, non-condensing. Storage −40 to +85°C; 10–95% RH, non-condensing. Temperature coefficient ±0.03%/°C over 0–50°C. Vibration 10–500 Hz, 2 G; 10 minutes per cycle, 60 minutes along each X, Y and Z axis. Altitude derating Above 2000 m, reduce permissible ambient temperature by 3.5°C per 1000 m for fanless operation. Keep the adapter unobstructed and apply both input and temperature limits. The plotted operating-temperature range is not a full-power guarantee at every input voltage. Dimensions and Connections Enclosure dimensions, L × W × H 210 × 85 × 46 mm; drawing tolerance ±1 mm. Attached DC cable UL2464 16AWG × 4C; 1000 ±50 mm. Default DC plug R7B: Pins 1 and 4 +Vo; pins 2 and 3 −Vo. KYCON KPPX-4P equivalent. Grounding Class I, with protective earth through the 3-pole AC inlet; standard DC −V is connected to AC FG. AC cord The catalogue specifies the AC inlet but does not state that a detachable mains cord is included. Select a suitable region-approved cord for this inlet and load. Use the numbered connector drawing for orientation; do not infer pin numbers from a photograph. Match the mating connector, contacts and wire rating to the actual current. The alternative plug references below identify options, not extra items included with this adapter. Alternative DC Plugs and Accessories P1J Straight tuning-fork type; 5.5 mm OD × 2.1 mm ID × 11.0 mm length. P1M Straight tuning-fork type; 5.5 mm OD × 2.5 mm ID × 11.0 mm length. R7BF Pins 1 and 4 +Vo; pins 2 and 3 −Vo. Female locking 4-pin DIN, KYCON KPJX-CM-4S equivalent. R1B Pins 1, 2 and 4 −Vo; pins 3 and 5 +Vo. Male 5-pin DIN. MIC4 Pins 1 and 2 +Vo; pins 3 and 4 −Vo. NEUTRIK XLR NC4FX equivalent. C6P Pins 1–3 +Vo; pins 4–6 −Vo. MOLEX 39-01-2060 equivalent, 4.2 mm pitch. The optional output connector is not connected to FG. C4P Pins 1 and 2 +Vo; pins 3 and 4 −Vo. AMP 1-480702-0 equivalent, 6.35 mm pitch. The optional output connector is not connected to FG. Stripped and tinned leads Available by customer request: lead 1 +Vo, lead 2 −Vo; standard exposed lengths L = 25 mm and L1 = 5 mm. Wire colors are illustrative; follow the delivered product. Alternative terminations can be specified as a customized cable subject to minimum order quantity. Only the options explicitly marked as quick adapters are available as separate accessories without minimum order quantity; the plug kit is sold separately. P1J and P1M quick adapters are listed for 48 V output only, with a 7.5 A maximum accessory current rating. Confirm the complete accessory configuration, polarity and allowable current before ordering. Safety and EMC Catalogue safety approvals UL62368-1, CSA C22.2 No.62368-1, TUV BS EN/EN62368-1, BSMI CNS15598-1, CCC GB4943.1, PSE J62368-1, AS/NZS 62368.1, BIS IS13252, KC K60950-1 and EAC TP TC 004. Energy-saving compliance EISA 2007/DoE, NRCan, Korea K-MEPS, AU/NZ MEPS and EU ErP and CoC Version 5. Withstand voltage Input/output: 3 kVAC; input/FG: 2 kVAC; output/FG: shorted. Insulation resistance Input/output: 100 MΩ at 500 VDC, 25°C and 70% RH. Conducted and radiated emissions Class B under BS EN/EN55032 (CISPR32), FCC Part 15 / CISPR22 and CAN ICES-3(B)/NMB-3(B); EAC TP TC 020. Also listed: CNS15936, GB17625.1 and MSIP KN32. Harmonic current / flicker BS EN/EN61000-3-2 Class A and GB9254; BS EN/EN61000-3-3. ESD immunity BS EN/EN61000-4-2: 15 kV air and 8 kV contact, Level 4. RF field / EFT immunity BS EN/EN61000-4-3: 3 V/m, Level 2; -4-4: 1 kV, Level 2. Surge immunity BS EN/EN61000-4-5: 1 kV line-to-line and 2 kV line-to-FG, Level 3. Conducted / magnetic immunity BS EN/EN61000-4-6: 3 V, Level 2; -4-8: 3 A/m, Level 2. Voltage dips and interruptions BS EN/EN61000-4-11: >95% dip for 0.5 periods, 30% dip for 25 periods, and >95% interruption for 250 periods. Generic immunity standard BS EN/EN55035. The adapter is considered an independent unit, but the complete equipment must still be checked for compliance with applicable EMC directives in its actual installation. Use approvals applicable to the exact model and market. Weight and Reliability Catalogue weight reference 1100 g: catalogue packing reference per unit; not a measured net or shipping weight. Packing 1.1 kg per unit; 12 pieces / 14.2 kg / 0.81 CUFT. MTBF, minimum estimates 2006.1 thousand hours, Telcordia SR-332 (Bellcore); 209.4 thousand hours, MIL-HDBK-217F at 25°C. Manufacturer warranty 3-year manufacturer warranty, subject to applicable terms. Catalogue revision 2026-04-03. For connector orientation and complete dimensions, refer to PDF pages 81–85.

  Read more less

  $160.18

  View options

Show more products